Name: Ryobi RCS3535B
Brand: Ryobi
Rating: 4 (1 reviews)

To Next Page

To Previous Page

English

EN DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG

FR DE ES IT PT NL SV DA NO FI

FR EN ES IT PT NL SV DA NO FI

FR EN DE IT PT

NL SV DA NO FI

FR EN DE ES NL SV DA NO FI

FR EN DE ES IT NL SV DA NO FI

FR EN DE ES IT PT SV DA NO FI

FR EN DE ES IT PT NL DA NO FI

FR EN DE ES IT PT NL SV NO FI

FR EN DE ES IT PT NL SV DA FI

FR EN DE ES IT PT NL SV DA NO

HU CS RU RO PL SL HR

ET LT LV SK BG

FR EN DE ES IT PT NL SV DA NO FI

CS RU RO PL SL HR ET LT LV SK BG

HU RU RO PL SL HR

HU CS RO PL SL HR

HU CS RU PL SL HR

HU CS RU RO SL HR

HU CS RU RO PL HR

HU CS RU RO PL SL

ET LT LV SK BG

FR EN DE ES IT PT NL SV DA NO FI

HU CS RU RO PL SL HR

LT LV SK BG

ET LV SK BG

ET LT SK BG

ET LT LV BG

ET LT LV SK

■ Do not use any type of pre-mixed petrol/lubricant

from fuel service stations; this includes the pre-

mixed petrol/lubricant intended for use in mopeds,

motorcycles, etc.

■ Use a high quality 2-cycle self-mixing lubricant for air-

cooled engines. Do not use automotive lubricant or

2-cycle outboard lubricant.

■ Mix 2% lubricant into the petrol. This is a 50:1 ratio.

■ Mix the fuel thoroughly and each time before fuelling.

■ Mix in small quantities. Do not mix quantities larger

than usable in a 30-day period. A 2-cycle lubricant

containing a fuel stabilizer is recommended.

1 litre + 20 ml =

2 litres + 40 ml =

3 litres + 60 ml = 50: 1

4 litres + 80 ml =

5 litres + 100 ml =

 Fuel system damage or performance problems

resulting from the use of an oxygenated fuel containing

more than the percentages of oxygenates stated

previously are not covered under warranty.



See Figure 5.

■ Clean the surface around the fuel cap to prevent

contamination.

■ Loosen the fuel cap slowly.

■ Carefully pour the fuel mixture into the tank. Avoid

spillage.

■ Prior to replacing the fuel cap, clean and inspect the

gasket.

■ Immediately replace the fuel cap and hands tighten it.

Wipe up any fuel spillage.

  It is normal for the engine to emit smoke during

and after the first use.



See Figure 6.

Use Ryobi Bar and Chain Lubricant. It is designed for

chains and chain oilers, and is formulated to perform over

a wide temperature range with no dilution required. The

chainsaw should use approximately one tank of lubricant

per tank of fuel.

 Do not use dirty, used, or otherwise contaminated

lubricants. Damage may occur to the lubricant pump, bar,

or chain.

■ Carefully pour the bar and chain lubricant into the

lubricant tank.

■ Fill the lubricant tank every time you fuel the engine.



See Figures 7 - 8.

Check the operating condition of the chain brake prior to

each use.



■ Engage the chain brake by rotating your left hand

around the front handle, allowing the back of your

hand to push the chain brake lever/hand guard

toward the bar while the chain is rotating rapidly. Be

sure to maintain both hands on the saw handles at all

times.

■ Reset the chain brake back into the RUN position by

grasping the top of the chain brake lever/hand guard

and pulling toward the front handle until you hear a

click.



If the chain brake does not stop the chain

immediately, or if the chain brake will not stay

in the run position without assistance, take the

saw to an authorised service centre for repair

prior to use.

STARTING THE ENGINE

See Figures 8 - 13.

Starting the product differs depending on whether the

engine is cold or warm.



Keep your body to the left of the chain line.

Never straddle the saw or chain, or lean over

past the chain line.

■ Place the chainsaw on level ground and ensure

that no objects or obstructions are in the immediate

vicinity that could come in contact with the bar and

chain.

■ Hold the front handle firmly with your left hand and

put your right foot onto the base of the rear handle.



■ Turn on the ignition switch.

■ Make sure the chain brake is in the run position by

pulling back on the lever/hand guard.

■ Fully press and release the primer bulb at least 7

times.

■ Pull choke lever all the way out to START position.

}

Ryobi RCS3535B User Manual

Table of Contents

Questions and Answers:

Ryobi RCS3535B Specifications

Related product manuals

Brand	Ryobi
Model	RCS3535B
Category	Chainsaw
Language	English