Samsung SNF-7010 - User Manual

Other manuals for Samsung SNF-7010

Specification2 pages

Questions and Answers

T
Timothy SpencerAug 16, 2025
What to do if Samsung Security Camera does not operate properly with Micro SD memory card inserted?
- D
  Douglas WilliamsAug 16, 2025
  If a Micro SD memory card is inserted but the Samsung Security Camera does not operate properly: 1. Check if the memory card is inserted in the proper direction. 2. Note that the operation of a memory card formatted by other devices is not guaranteed with this camera unit. 3. Format the memory card again in the camera's Setup > Event > Storage menu.
H
Hannah ValenciaAug 18, 2025
Why can't I access my Samsung SNF-7010 Security Camera from a web browser?
- M
  manntheresaAug 19, 2025
  If you're unable to access the camera from a web browser, verify the camera’s network settings are correct. Also, ensure all network cables are properly connected. If using DHCP, confirm the camera obtains dynamic IP addresses without issues. If connected to a broadband router, check that port forwarding is correctly configured.
Z
Zachary FoleyAug 22, 2025
What to do if my Samsung SNF-7010 Security Camera viewer got disconnected during monitoring?
- S
  Sarah BookerAug 22, 2025
  If connected viewers disconnect during monitoring, this can happen upon changes to the camera or network configurations. Ensure you check all network connections. If the camera is connected over a PPPoE network, the viewer might disconnect under poor network conditions.
S
Spencer JamesAug 25, 2025
Why is of set to , but no notification e-mail reaches me even when a motion event had occurred on my Samsung SNF-7010 Security Camera?
- N
  nielsenelizabethAug 25, 2025
  If you are not receiving notification emails when motion is detected, verify the settings in the following sequence: 1. Check settings. 2. The should be set to . 3. Check if the option of menu is checked to use.
R
Richard SolomonAug 27, 2025
Why do images overlap on my Samsung Security Camera?
- L
  Laura FriedmanAug 27, 2025
  If images overlap, check whether two or more cameras are set to a single multicast address instead of different addresses. If a single address is used for multiple cameras, the images may overlap.
M
Michael DavisAug 31, 2025
Why is my Samsung SNF-7010 Micro SD memory card inserted but the camera does not operate properly?
- A
  Andrew AllenAug 31, 2025
  If the camera does not operate properly with the Micro SD card inserted: * Check if the memory card is inserted in the proper direction. * Operation of a memory card that is formatted by other devices is not guaranteed with this camera unit. * Format the memory card again in ? ? menu.
E
elizabeth46Sep 3, 2025
How to connect to the Samsung Security Camera system using a tab browser of Internet Explorer 7.0?
- D
  dcarsonSep 3, 2025
  To connect without errors, do not use a new window or tab. Instead, select “File ? New session,” as errors may occur due to shared cookie data when connecting with a new window or tab.
D
David VaughnSep 5, 2025
How to fix Samsung Security Camera when I can’t access it from a web browser?
- S
  susanjohnsonSep 6, 2025
  If you cannot access your Samsung Security Camera from a web browser, ensure the camera's network settings are correctly configured. Also, verify that all network cables are properly connected. If using DHCP, confirm the camera obtains dynamic IP addresses without issues. If connected to a broadband router, check that port forwarding is correctly set up.
P
perezsarahSep 9, 2025
Why am I not receiving email notifications from my Samsung SNF-7010 Security Camera when motion is detected?
- B
  Brian JenkinsSep 9, 2025
  If motion detection is enabled in the event setup, but you are not receiving notification emails from your Samsung Security Camera when motion is detected, check the following settings in sequence: 1. Verify the data and time settings. 2. Ensure motion detection is enabled. 3. Confirm the email option in the event action setup menu is checked.
J
johnsonthomasSep 12, 2025
How to connect to Samsung Security Camera without using a new window or tab in Internet Explorer 7.0?
- C
  contrerasmarkSep 12, 2025
  If you cannot connect to the system using a tab browser of Internet Explorer 7.0 with your Samsung Security Camera, an error may be generated when connecting with a new window or tab since the cookie data are shared. Do not use a new window or tab, select 'File ? New session'.

Summary

Overview

Important Safety Instructions

Essential safety precautions to follow before installing and operating the network camera.

Installation & Connection

Installation Precautions

Guidelines and precautions to ensure a safe and proper installation of the camera.

Camera Installation

Step-by-step instructions for mounting the camera on a ceiling or wall.

Outdoor Installation

Micro SD Memory Card Handling

Network Connection and Setup

Local Area Network Connection

Steps to connect the camera to a local network and access it via a PC.

DHCP Modem Connection

PPPoE Modem Connection

Broadband Router Connection

Static IP Setup

Guide to manually configure static IP address settings for the camera.

Dynamic IP Setup

Web Viewer Usage

Connecting to the Camera

Methods to connect to the camera via IP address or URL using a web browser.

Login Procedure

Steps to log in to the camera's web interface using default credentials.

Live Screen Operations

Snapshot and Video Playback

Setup Screen Configuration

Video & Audio Setup

Network Setup

Configuring network interfaces, ports, DDNS, IP filtering, SSL, and protocols.

Event Setup

Troubleshooting

Problem and Solution Guide

Common problems encountered and their solutions for web browser access, disconnection, and image issues.

Samsung SNF-7010 Specifications

General

Model	SNF-7010
Category	Security Camera
Lens Type	Fixed
Aperture	F2.0
Video Compression	H.264, MJPEG
Network Interface	RJ-45 (10/100BASE-T)
Power Supply	PoE (IEEE802.3af)
Max Resolution	2048 x 1536
Resolution	2048 x 1536
Wide Dynamic Range	DWDR
Protocols	TCP/IP, UDP/IP, RTP, RTSP, HTTP, HTTPS, SSL, DHCP, SMTP, SNMPv1/v2c/v3(MIB-2), ARP
Operating Temperature	-10°C