GB
17
NICAM
★
(SV-665GX/ SV-661GX
Only)
Selecting the Cassette Type
Switching between the TV and VCR
Modes
The TV/VCR button allows you to record one
channel with the VCR while you watch another
channel on the TV.
When the VCR Your television...
indicator is...
On
The television receives the
picture from the VCR and you
can select channels with the
PROG/TRK (
or
❷
) / PROG
(
or
❷
)
buttons on the VCR or
the remote control.
Off (or the VCR The television receives the is
turned off) picture from your home aerial or
cable television system as it did
before you connected the VCR.
You can then use the
programme
(
or
❷
) buttons on your
television to select the channels.
To switch the VCR indicator on and off, simply press
the TV/VCR button.
Selecting the Recording Speed
★
(SV-665GX/SV-661GX/
SV-465GX/SV-461GX Only)
You can record a cassette at two different speeds:
◆ SP (Standard Play)
◆ LP (Long Play)
In Long Play modes:
◆ Each cassette lasts twice as long
◆ The recording is of a slightly lower
quality
To record a cassette... Press the SPEED button
on the remote control,
until...
In standard play mode SP is displayed.
In long play mode
LP is displayed.
T
ype Recording Time (in SP)
E-180 180 mins. or 3 hours
E-240 240 mins. or 4 hours
E-260 260 mins. or
4 hours and 20 mins.
E-300 300 mins. or 5 hours
GB
16
Clearing a Preset Station
Presetting the Stations Manually
☛ You do not need to preset the stations
manually if you have already set them
automatically.
➢ To enable the VCR to decode a scrambled
TV station, the decoder must be switched on.
1 Press the MENU button on the remote control.
Result
: The programming menu is displayed.
2 Press the corresponding
,
❷
or
➛
,
❿
buttons to
select the
INSTALLATION option.
3 Press the OK button to select this option.
Result
: The INSTALLATION menu is displayed.
4 Press the corresponding
or
❷
buttons, until the
MANUAL SET UP option is selected.
5 Press the
❿
button to select MANUAL SET UP option.
Result
: The TV STATION TABLE menu is displayed.
6 Press the
or
❷
buttons to select a programme
number as required.
7 Press the
❿
button to preset the station.
Result: The MANUAL TUNING menu is displayed.
8 Press the
➛
or
❿
buttons to start scanning.
Result
: The frequency band is scanned and the first
station found is displayed.
If you know the number of the channel you want,
press the numeric buttons on the remote control for
example, for channel E21, first press “0” and then
press “2”, “1” (see page 29).
9 Press the
❷
button, until the DECODER is selected.
10 Press the
❿
button to activate or deactivate use of
the decoder for the TV station, if necessary.
11 Press the
or
❷
buttons until the NAME is selected.
12 To change the programme’s name, press the
❿
button.
Result
: The first letter of the name flashes.
13 To... Then...
Select a character Press the
or
❷
button until
in the name
the required character is displayed
(letters, numbers or “-” character).
Move to the next or Press the
❿
or
➛
buttons
previous character respectively.
14 If you... Then...
Wish to store the ◆
Press the corresponding
station displayed or
❷
buttons, until the MFT
is selected.
◆ Press the
➛
or
❿
buttons to
adjust the picture, if necessary.
◆
Press OK to store the station .
Do not
wish to
◆
Press the corresponding
store the station or
❷
buttons, until the CH
displayed is selected.
◆ Press the
➛
or
❿
buttons to
go on scanning the frequency
band and display the next
station
◆ Go back to the beginning of
Step
14
15 Repeat this procedure from Step 6 onwards, until all
the required stations have been stored.
16
On completion, press the MENU button three times to
exit the menu.
Changing the Preset Station Table
You can rearrange the preset TV stations according to your
own preferences programme number assigned to the station.
1 Press the MENU button on the remote control.
Result: The programming menu is displayed.
2 Press the corresponding
,
❷
or
➛
,
❿
buttons to
select the INSTALLATION option.
3 Press the OK button to select this option.
Result: The INSTALLATION menu is displayed.
4 Press the corresponding
or
❷
buttons, until the
MANUAL SET UP option is selected.
Result
: The TV STATION TABLE menu is displayed.
5 Press the corresponding
or
❷
buttons, until the
required preset TV programme is selected.
Result: The selected station is displayed at the same
time on the television screen.
6 To change the programme number assigned to a
station press the OK button on the remote control.
(For example, To move a TV station in programme 1
to programme 3)
7 Press the
or
❷
buttons to select required position.
And then press OK again to swap the position.
8 You can modify this station by repeating the same
procedure from Step
5 onwards.
9 On completion, press the MENU button three times
to exit the menu.
If you have stored a TV station:
◆ That you do not require
◆ At the wrong programme position
you can cancel it.
1 Press the MENU button on the remote control.
Result
: The programming menu is displayed.
2 Press the corresponding
,
❷
or
➛
,
❿
buttons to
select the
INSTALLATION option.
3 Press the OK button to select this option.
Result
: The INSTALLATION menu is displayed.
4 Press the corresponding
or
❷
buttons, until the
MANUAL SET UP option is selected.
5 Press the
❿
button to select this option.
Result: The TV STATION TABLE menu is displayed.
6 Press the corresponding
or
❷
buttons, until the
required preset TV station (PR) is selected.
7 Press the CLR/RST button.
8 Repeat the same procedure from Step 6 onwards
until all the required stations have been cleared.
9 On completion, press the MENU button three times
to exit the menu.
If you wish to use the tape counter to display the
time remaining on a cassette, you must indicate the
type of cassette inserted.
1 Press MENU on the remote control.
Result
: The programming menu is displayed.
2 Press the corresponding
,
❷
or
➛
,
❿
buttons to
select the
USER SET option.
3 Press the OK button to select this option.
4 Press the corresponding
or
❷
buttons, until the
TAPE SELECT option is selected.
5 Press the
➛
or
❿
buttons as many times as
required, until the correct cassette length is
displayed.
E180 E240
E 300 E260
6 Press MENU twice to exit the menu.
NICAM programmes are divided into 3 types. NICAM
Stereo, NICAM Mono and Bilingual (transmission in
another language). NICAM programmes are always
accompanied by a standard mono sound broadcast and
you can select the desired sound. Please refer to page 22.
1 Press MENU on the remote control.
Result: The programming menu is displayed.
2 Press the corresponding
,
❷
or
➛
,
❿
buttons to
select the USER SET option.
3 Press the OK button to select this option.
Result: The USER SET menu is displayed.
4 Press the corresponding
or
❷
buttons, until the
NICAM option is selected.
5 To... Press
➛
or
❿
, until...
Mono mode OFF is displayed.
OFF: Only set at this position to
record the standard mono
sound during a NICAM
broadcast if the stereo
sound is distorted due to
inferior reception conditions.
NICAM mode ON is displayed.
ON: Normally set at this position.
6 On completion, press MENU twice to exit the menu.
To Next Page
Loading...
Need help?
General
