GB
27
GB
26
Your VCR remote control will work with Samsung
televisions and compatible brands.
To determine whether your television is compatible,
follow the instructions below.
1 Switch your television on.
2 Point the remote control towards the television.
3 Hold down the TV button and enter the two-figure
code corresponding to the brand of your television,
by pressing the appropriate numeric buttons.
Brand Codes Brand Codes
SAMSUNG 01 to 06 PHILIPS 02, 20, 22
AKAI 09, 23 SABA 13, 14, 22 to 24
GRUNDIG 09, 17, 21 SONY 15, 16
LOEWE 02 THOMSON 13, 14, 24
PANASONIC 08, 23 to 27 TOSHIBA 07, 16 to 19, 21
Result:
If your television is compatible with the
remote control, it is switched off. It is now
programmed to operate with the remote
control.
➢ If several codes are indicated for your television
brand, try each one in turn until you find one that
works.
☛
When you change the batteries in the remote
control, you must reprogramme the code,
following the same procedure.
The Auto Power Off feature automatically turns off
your VCR if no signal is received and you do not
press any button for the selected time.
1 Press MENU on the remote control.
Result
: The programming menu is displayed.
2 Press the corresponding
,
❷
or
➛
,
❿
buttons to
select the
EASY OPERATION option.
3 Press the OK button to select this option.
Result
: The EASY OPERATION menu is displayed.
4 Press the corresponding
or
❷
buttons, until the
AUTO POWER OFF option is selected.
5 Press the
❿
button, until you select the time of Auto
Power off interval.
OFF 2HOUR 3HOUR
6 On completion, press MENU twice to exit the menu.
Auto Power Off
ECO Mode-Reducing Standby
power consumption
Technical Specifications
Low Power Mode reduces the Standby power
consumption of the VCR when in Standby mode.
Useful, for example, when you are away from the
house on holiday. It saves actually turning the VCR off.
1 Press MENU on the remote control.
Result: The programming menu is displayed.
2 Press the corresponding
,
❷
or
➛
,
❿
buttons to
select the
USER SET option.
3 Press the OK button to select this option.
Result: The USER SET menu is displayed.
4 Press the corresponding
or
❷
buttons, until the
ECO. MODE is selected.
5 Press the
❿
button to turn LOW(3Watts) mode on.
Now, when the VCR is standby mode the front
display panel will shut off. Even the clock disappears.
By pressing the VCR STANDBY/ON (STANDBY/ON)
button again the display panel will reappear.
6 On completion, press MENU twice to exit the menu.
MODEL SV-665GX/SV-661GX SV-465GX/SV-461GX/SV-265GX/SV-261GX
Design and specifications are subject to change without notice.
Format VHS PAL standard VHS PAL standard
Heads Video: 4 rotary heads
Video: 4 rotary heads (SV-465GX/SV-461GX)
Video: 2 rotary heads (SV-265GX/SV-261GX)
Hi-Fi audio: 2 rotary heads
Audio/Control: 1 stationary head Audio/Control: 1 stationary head
Erase: 1 full track erase head Erase: 1 full track erase head
Receiving channel VHF-I, VHF-III, UHF, Interband/Hyperband VHF-I, VHF-III, UHF, Interband/Hyperband
Television system STANDARD B/G-D/K-A2/NICAM STANDARD B/G-D/K
Luminance FM azimuth recording FM azimuth recording
Colour system
PAL/MESECAM/NT4.43: Down converted
subcarrier
PAL/MESECAM/NT4.43: Down converted
subcarrier
phase shifted direct recording NTSC PB on PAL TV phase shifted direct recording NTSC PB on PAL TV
Tape speed SP 23.39 mm/sec SP 23.39 mm/sec
LP 11.69 mm/sec LP
11.69 mm/sec (SV-465GX/SV-461GX)
Recording/playback time SP 3 hours (E-180 Tape) SP 3 hours (E-180 Tape)
LP 6 hours (E-180 Tape) LP 6 hours (E-180 Tape) (SV-465GX/SV-461GX)
REW time About 60 sec in REW with E-180 About 60 sec in REW with E-180
VIDEO
Input 0.5 to 2.0 Vp-p; 75 ohm unbalanced 0.5 to 2.0 Vp-p; 75 ohm unbalanced
Output 1.0 ± 0.2 Vp-p; 75 ohm unbalanced 1.0 ± 0.2 Vp-p; 75 ohm unbalanced
Signal-to-noise ratio Better than 43 dB (SP) Better than 43 dB (SP)
Horizontal resolution More than 240 lines More than 240 lines
AUDIO
Input -8 dBm, 47 Kohm unbalanced -8 dBm, 47 Kohm unbalanced
Output -8 ± 3 dBm, 1 Kohm unbalanced -8 ± 3 dBm, 1 Kohm unbalanced
Wow and flutter (WTD) 0.4% max (SP) 0.4% max (SP)
Signal-to-noise ratio 68 dB min (IHF A filter) 42 dB min (IHF A filter)
Frequency response 20Hz - 20kHz 100Hz - 8kHz
Power requirement 220-240V~ 50Hz 220-240V~ 50Hz
Power consumption Approx. 17 watts Approx. 15 watts
Operation temperature 41°F-104°F (5°C-40°C) 41°F-104°F (5°C-40°C)
Operation humidity 10%-75% 10%-75%
Weight 2.8 Kg (net) 2.8 Kg (net)
Dimensions (WxHxD) 360 x 94 x 240 mm 360 x 94 x 240 mm
Using the TV Buttons on the Remote Control
★
(SV-665GX Only)
You can then control the television using the following
buttons.
Button Function
TV STANDBY/ON
Used to switch the television on
and off.
TV or VCR Used to switch between the TV
and VCR modes. Only the VOL
(
+ or –
)
and TV STANDBY/ON
buttons are operational in VCR
mode.
-/-- Used to enter a two-figure
programme number.
Example: For programme 12,
press -/-- followed by numeric
buttons 1 and 2.
INPUT Used to select an external
source.
VOL + or –
Used to adjust the volume of the
television.
PROG/TRK Used to select the required
( or❷)
programme.
DISP./
Used to switch between an external
source and the television tuner.
➢
The various functions will not necessarily
work on all televisions. If you encounter
problems, operate the television directly.
To Next Page
Loading...
Need help?
General
