S&C 6800 Series - User Manual

Setup
Table of Contents
Section Page Section Page
Introduction
Qualified Persons .......................... 2
Read this Instruction Sheet ................... 2
Retain this Instruction Sheet. . . . . . . . . . . . . . . . . . . 2
Special Warranty Provisions ................... 2
Safety Information
Understanding Safety-Alert Messages ........... 4
Following Safety Instructions .................. 4
Replacement Instructions and Labels ........... 4
Safety Precautions ...........................5
IntelliLink® Setup Software
Applicable Software ......................... 6
Software Overview .......................... 7
Computer Requirements ..................... 7
IntelliLink® Setup Software License Activation .... 8
Installing a License Activation File . . . . . . . . . . . . . . 9
Starting IntelliLink Software ...................11
Navigating IntelliLink Screens .................11
IntelliLink Workspace ........................16
Switch Control Setup
Setup General Screen ...................... 20
Sensor Configuration ....................... 22
Site-Related Configuration ................... 25
Metering Data ............................. 28
Fault Detection Configuration ................ 29
Automatic Operation Configuration ...............37
User Commands Configuration ............... 44
Hot Line Tag .............................. 45
Shots to Lockout ........................... 45
Time Configuration ........................ 46
Firmware Revisions ........................ 49
User Notes ............................... 49
Team RTU Addresses ...................... 50
Team Setup ...............................51
External Loading ........................... 56
Team Communication Parameters ............ 58
Distributed Generation ...................... 59
Restoration—External Device .................61
Communications Setup ..................... 64
Serial Ports ............................... 70
Routing ..................................71
Ethernet Settings .......................... 72
Wi-Fi Settings ..............................74
Communication Tests ....................... 75
DNP Diagnostics .......................... 77
DNP Status Point Mapping .................. 78
DNP Double-Bit Status Point Mapping ......... 80
DNP Analog Input Point Mapping ...............81
DNP Control Point Mapping .................. 82
DNP Analog Output Point Mapping ............ 83
DNP Counter Point Mapping ................. 84
Security Settings .......................... 85
Log Management .......................... 86
Setup Validate/Apply ........................ 89
January 28, 2019
© S&C Electric Company 2011-2019, all rights reserved
Instruction Sheet 1045-530
S&C 6800 Series Automatic Switch Controls with
IntelliTeam
®
SG Automatic Restoration System

S&C 6800 Series Specifications

General

Trip Coil Voltage	125 VDC
Close Coil Voltage	125 VDC
Continuous Current Rating	1200 A
Interrupting Rating	25 kA
Enclosure Type	NEMA 4X

Summary

Introduction and Safety

Introduction and Warranty

Provides information on qualified personnel, document retention, and warranty terms for the equipment.

Safety Alerts and Instructions

Details safety alert message types, importance, and instructions for safe operation and maintenance.

Safety Precautions

Outlines critical safety precautions, including qualified persons, procedures, and PPE for safe operation.

IntelliLink Software and Workspace

IntelliLink Setup Software Requirements

Specifies software versions, computer requirements, and steps for license activation.

IntelliLink Software Operations

Guides users on starting the IntelliLink software and navigating its operation and screen elements.

IntelliLink Workspace Overview

Explains the IntelliLink software user interface, including toolbar, navigation, and screen area.

Switch Control Setup

General Configuration

Configures general settings like device identification, logging levels, and cabinet heater parameters.

Sensor, Metering, and Site Data

Sets up sensor calibration, metering values, site-related parameters, and voltage thresholds.

Fault Detection and Automatic Operation

Configures parameters for fault detection, sectionalizing, phase loss protection, and auto-reclose.

User Commands, Time, and Revisions

Customizes user commands, Hot Line Tag, Shots to Lockout, time settings, and firmware revisions.

IntelliTeam SG Restoration and Teams

Configures IntelliTeam SG system parameters, team setup, RTU addresses, and restoration.

Communications and Network Settings

Manages DNP settings, serial ports, routing, Ethernet, Wi-Fi, and communication tests.

Point Mapping and Diagnostics

Configures DNP points for SCADA mapping and performs communication diagnostics.

Security and Log Management

Manages user access security and configures logging levels and event management.

Validate and Apply Settings

Provides tools to validate, apply, and reset configuration settings to the control.