LISTENING TO TAPES
‘—.—
.
I
1. Press the FUNCTION button to select “TAPE.
2. Press the STOP/EJECT button to open the cassette holder.
3, Load the cassette.
After loading the cassette, push the
cassette holder back into position.
4. Press the PLAY button to begin playback.
m
@
o
5. Press the STOP/EJECT button to stop
playback at any time. Press it again to
remove the cassette.
w
When the end of the tape has been
reached, automatic stop will be activated.
Note:
Use the normal tape (TYPE 1).
Endless tapes cannot be used.
Do not use C-100 (or longer) tapes. They may jam in the mechanism.
Pause
Press the PAUSE button to temporarily stop playback or recording. Press
it again to resume operation.
Fast forward and rewind
Press the F FWD or REW button. When the desired location has been
reached, press the STOP/EJECT button.
LISTEN,I,NG TO THE RADIO
...
Before use
When the unit is shipped from the factory, its AM frequency band is set as
“522 -1710 kHz (in 9 kHz steps)”.
If your local AM broadcast system is organized in 10 kHz steps, change
the frequency band to ‘(520 -1710 kHz (in 10 kHz steps)” as follows.
1. Press the TUNER/BAND button to select “AM”.
2. While pressing the MEMORY button on the front panel, press the
TUNER/BAND button on the front panel.
To return the original setting, repeat steps above.
[
To turn the unit on and listen to the last received station, press the
TUNER/BAND button.
I
Automatic/Manual tuning
1.
2.
Press the TUNER/BAND bu~on to select FM or AM.
“TUNER” is selected automatically. “TUNER” appears on the
display, then ‘TUNER” is replaced by the tuner mode display.
Automatic tuning
Press the + or – ~UNING button for at least 1 second to tune in a
station. The unit will scan up or down the band and receive the next
receivable station. Press the button again to continue.
The ›>~Fl or~~<< button on the remote control can also be
used.
Manuaf tuning
Press the + or – TUNING button briefly until the desired frequency IS
displayed.
1: h/1 I l–l 3 –11– w
I I f I l_l _l.1: :1
To preset stations
Up to 24 stations for FM band, and up to 12 stations for AM band can be
preset.
Automatic presetting (APT) (Main unit only)
1. Press the TUNER/BAND button to select FM or AM.
2. Press the MEMORY button for at least 3 seconds. “PROG.” blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 stations for FM, 12 stations for AM have been preset or the
hiah end af the band is reached. autamatic oresettino stow.. “PROG.”
disappears and the previous received station is heard.
3. To preset stations on the other band, follaw steps above.
Note:
If APT is activated, all previously programmed stations of the band will be
cleared and new stations will be programmed.
Manual 1.3resettincf
1.
2.
3.
4.
5.
Tune in the st~tion to be preset as described in “Automatic/Manual
tuning”.
Press the MEMORY button.
\l/
m 1— II/l
1313’17 f “.
f--n I f~’l_l I
Press the FF+PI or 1<4<< button an the front panel (or PRESET
button on the remote control) to select the channel number to be
I.Meset.
Press the MEMORY button.
In this example,”1 03.25 MHz” FM station is preset an FM channel
9.
- The number buttons on the remote control can be used to preset
the station directly. In this example, press O,then 9 after the step
2 above.
1: 1~d I IT :1 :11: U*
f f I ll_l_l.l_ _l
Note:
If the next step is not taken within 2 seconds while performing steps
2-4, “PROG.” disappears and the preset operation is cancelled.
Press the MEMORY button to continue.
Repeat steps above to add more preset stations.
When presetting a new station, the previous preset station is cleared.
Listening to preset stations
1. Press the TUNER/BAND button to select FM or AM.
2. Press the ➤>SN or M4/+4 button on the front panel (or PRESET
button on the remote control) to select the desired channel number.
The selected channel number appears briefly.
The number buttons on the remote control can also be used.
Press two number buttons within 2 secands.
To receive FM stereo broadcasts (Remote control only)
Make sure that “MONO is not displayed. If “MONO appears, press the
FM MODE button to turn the ‘(MONO indication off.
“S~ appears when an FM stereo braadcast is received.
If the signal from an FM sterea station is weak and reception is poor,
press the FM MODE button to change to the MONO mode. The
reception may be improved, but the sound will be monaural.
LISTENING TO OTHER SOURCES
..-..—.-).
.
........“.
.~
1. Press the FUNCTION button to select “VIDEO:AUX.
2. Follow the instructions supplied with the Video/Auxiliary equipment.
.G.
To Next Page
Loading...
