~ .,.,.,~S_TENING To T~~ Ralo
..
To turn the unit on and listen to the last received station, press the
TUNEWBAND button.
Automatic/Manual tuning
1.
2.
Press the TUNEWBAND bu{on to select the desired band.
‘TUNER” is selected automatically. ‘TUNE” appears on the
display, then 71JNE” is replaced by the tuner mode display.
For UK: FM — MW— LW
For AU: FM — AM
Automatic tuning
Press the + or - TLfNING button (more than 0.7 seconds) to tune in
a station. The unit will scan up or down the band and receive the next
receivable station. Press the button again to continue.
Manual tuning
Press the + or – TUNING button briefly (less than 0.7 seconds) until
the desired frequency is displayed. Each time the button is pressed,
the frequency changes in 0.05 Mt-fz steps for FM, 9 kHz steps for MW/
AM and LW.
To preset stations
For UK: Up to 24 stations for FM band, 12 stations for MW band, and up
to 4 stations for LW band can be preset. -
For AU: Up to 24 stations for FM band, and up to 12 stations for AM band
can be preset.
Automatic presetting (APT)
1. Press the TUNEWBAND button to se!ect the desired band.
2. Press and hold down the MEMORY button for at least 3 seconds.
“PROG.” blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 stations~12 stations for MLWAM or 4 stations for LW) have
been preset or the high end of the band is reached, automatic
presetting stops. “PROG.” disappears and the station memorized on
channel number 1 will be heard.
3. To preset stations on the other ban@, follow steps above.
Note:
If APT is activated, all previously prograrn!rrred stations of the band will be
cleared and new stations will be programmed.
Manual presetting
1. Tune in the station to be preset as described in “AutomatidManual
tuning”.
2. Press the MEMORY button.
?
—.
;2 3.2Q?
3. Press the+ or – PRESET button t~ select the channel number to be
preset.
y
m till–jr
n IU3. C3*
4. Press the MEMORY button.
In this example,”1 03.25 MHz” FM station is preset on FM channel
number 9.
- The number buttons on the rermte control can be used to select
the preset station. In this exan%ale, press O,then 9 after the step
2 above.
,r ;V;
/g 3.?%
5.
Note:
If the next step is not taken within 10 seconds while performing steps
2 -4,, “PROG.” disappears and the preset operation is cancelled.
Pres& the MEMORY button to continue.
RepesX the steps above to add more preset stations.
When+ presetting a new station, the previously preset station on the
same channel number of the same band is cleared.
TFreEpreset stations will be retained in the memory even if the unit is
tumred
Off.
If the memory contents are lost due to a power failure or other
condition, prese~ the stations again.
Listerx3ng to preset stations
1.
Press the TUNEWBAND button to select the desired band.
2. Press the+ or- PRESET button (less than 0.7 seconds) to select the
desired channel number.
The number buttons on the remote control can also be used.
Press two number buttons within 4 seconds.
Preset scan tunina
1.
2.
3.
Press the TUN;IWBAND button to select the desired band.
Press the + PRESET button (more than 0.7 seconds). The channel
number blinks on the display. Each of the preset stations is tuned in
for 5 seconds.
When the desired slation has been tuned in, press the + PRESET
bdtcm again to keep the reception locked at that station.
To receive an FM stereo broadcast, make sure that “MONO” is not
displayed. If “MONO” appears, press the FM MODE button to turn the
“MQNO” indication off.
“ST” appears when an FM stereo broadcast is received.
If the sianal from an FM stereo station is weak and recePtion is poor,
press t;e FM MODE button to change to monaural reception. (“ST” is
r.epfaced by “MONO” in the display.)
When beat interference is heard
A high-pitched noise called “bear is sometimes heard during reception of
radio broadcasts.
If this occurs,
1. Press the MEMORY button.
2. While “PROG.” is bfinking, press the ~< /44 SKIP/SEARCH button
to select “bc-~ or “bC-b”. Select the setting that gives the best results.
Changing the MW/AM reception frequencies
It is not necessary to perform this procedure in the Europe (or in the
Australia and New Zealand).
1. Press the TUNER/BAND button to select “MW or “AM”.
2. While pressing the MEMORY button on the front panel, press the
■ STOP button [CD section) on the front panel.
For UK:
522-1611 kHz (9 kHz steps)
— 520-1610 kHz (10 kHz steps)
For AU:
522-1710 kHz (9 kl-fz steps)
— 520-1710 kHz (10 kHz steps)
12
To Next Page
Loading...
