To Next PageTo Next PageHow to fix a Sanyo SAP-KMRV93GJH Air Conditioner when the indoor unit operation lamp is flashing every 0.5 seconds?
If the indoor unit operation lamp is flashing every 0.5 seconds immediately after turning on your Sanyo Air Conditioner, this could indicate an external ROM (OTP data) failure on the indoor circuit board, a ROM socket insertion problem, or the ROM might not be installed. Check the indoor unit to troubleshoot.
What to do if no indicators illuminate and the indoor fan doesn't turn on my Sanyo SAP-KMRV93GJH Air Conditioner?
If no indicators light up and the indoor fan doesn't turn on your Sanyo Air Conditioner, check the power voltage.
Why does noise appear in the TV picture when using my Sanyo SAP-KMRV93GJH, or why is the picture distorted?
The noise or distortion in your television picture may be due to noise generated by the high-speed switching of the microcomputer and compressor in the Sanyo Air Conditioner. To resolve this, select a separate power source for the air conditioner.
General| Brand | Sanyo |
|---|---|
| Model | SAP-KMRV93GJH |
| Category | Air Conditioner |
| Language | English |
Lists indoor unit models SAP-KMRV93/123/183/243GJH and their product codes.
Important safety note regarding the use of R410A refrigerant.
Safety advice for handling, installing, and transporting the unit.
Guidelines for connecting refrigerant lines and performing service.
Specifies the acceptable indoor and outdoor temperature ranges for operation.
Detailed specifications for the SAP-KMRV93GJH indoor unit, including performance and electrical.
Detailed specifications for the SAP-KMRV123GJH indoor unit, including performance and electrical.
Detailed specifications for the SAP-KMRV183GJH indoor unit, including performance and electrical.
Detailed specifications for the SAP-KMRV243GJH indoor unit, including performance and electrical.
Lists major internal components for the SAP-KMRV93GJH unit, such as control PCB and motors.
Lists major internal components for SAP-KMRV123GJH and SAP-KMRV183GJH units.
Lists major internal components for the SAP-KMRV243GJH unit.
Graphs showing resistance values for indoor air temp, heat exchanger, and humidity sensors.
Physical dimensions and drawings for the SAP-KMRV93GJH indoor unit.
Physical dimensions and drawings for SAP-KMRV123GJH and SAP-KMRV183GJH indoor units.
Physical dimensions and drawings for the SAP-KMRV243GJH indoor unit.
Illustrates refrigerant flow for specific indoor unit models.
Charts showing air throw distance for the SAP-KMRV93GJH under cooling and heating conditions.
Charts showing air throw distance for the SAP-KMRV123GJH under cooling and heating conditions.
Charts showing air throw distance for the SAP-KMRV183GJH under cooling and heating conditions.
Charts showing air throw distance for the SAP-KMRV243GJH under cooling and heating conditions.
Wiring diagram and electrical data for the SAP-KMRV93GJH indoor unit.
Wiring diagrams and electrical data for SAP-KMRV123GJH and SAP-KMRV183GJH indoor units.
Wiring diagram and electrical data for the SAP-KMRV243GJH indoor unit.
Guidelines for choosing an appropriate location for installing the indoor unit.
Diagrams showing how to connect indoor units to the CMRV1923GJH outdoor unit.
Diagrams showing how to connect indoor units to the CMRV2433GJH outdoor unit.
Diagrams showing how to connect indoor units to the CMRV3143GJH outdoor unit.
Step-by-step guide to perform a test run after installation.
Describes controller functions like ON/OFF, TEST, DEMO, and automatic/manual operation modes.
Explains the HIGH POWER and ECONOMY modes for performance and energy saving.
Details protective measures against overload, freezing, and cold air during operation.
Procedure to change the remote controller address to avoid interference.
Steps to initiate and interpret the unit's self-diagnostic function.
Table listing diagnostic codes, items, and potential causes/contents.
Guidance on what to do if the self-diagnostics function itself fails.
Procedures for checking indoor/outdoor units and serial communication for faults.
Information on how high-frequency noise can affect the unit and how to correct it.
Highlights features like microprocessor control, timers, economy mode, and filters.
Explains the warning and caution symbols used throughout the manual.
Recommendations for choosing a suitable installation location.
Details on wiring, grounding, and electrical safety precautions.
Identifies the main parts of both the indoor and outdoor units.
Explains the function of the unit's operation selector and indicator lamps.
Defines the various symbols and icons shown on the remote control display.
Details the purpose and operation of each button on the remote control.
Instructions for using mode selection, flap adjustment, and fan speed controls.
Explains how to change the remote address and use the A/C sensor function.
Guide on how to insert and replace batteries in the remote control unit.
Step-by-step instructions for using the automatic operation mode.
Step-by-step instructions for operating the unit manually.
Further details and notes on performing manual operation.
How to adjust fan speed and activate the energy-saving Economy mode.
Explains how Economy mode adjusts temperature settings for energy saving in cooling/drying and heating.
Information on unit behavior during power outages and normal clicking sounds.
Instructions for setting the current time on the remote control unit.
Guide on how to program the unit to turn off automatically.
Guide on how to program the unit to turn on automatically.
How to set timers for daily repeating ON/OFF schedules.
Instructions for using the 1-Hour OFF Timer and HIGH POWER operation modes.
Advice on maintaining optimal performance and reducing energy consumption.
How to manually adjust the vertical vanes for left/right airflow.
How to use the remote to adjust the flap for vertical airflow and sweep function.
Instructions for operating the unit directly using the controls on the indoor unit.
Guide on how to clean the exterior of the indoor unit and its filters.
Instructions for maintaining the anti-mold and air cleaning filters.
Lists common issues, their possible causes, and recommended remedies.
Repeats operational temperature limits for cooling and heating.
