Sanyo SAP-KR165QS5 - User Manual

REMOTE
1
CONTROL UNIT
852.6.4189.212.01.1
INSTALLATION INSTRUCTIONS
Ð Split system air conditioner Ð
DECLARATION OF CONFORMITY
This product is marked as it satisfies Directives:
– Low voltage no. 73/23 EEC and 93/68 EEC.
– Electromagnetic compatibility no. 89/336 ECC, 92/31 EEC
and 93/68 EEC.
This declaration will become void in case of misuse and/or non
observance though partial of manufacturer's installation and/or
operating instructions.
COOLING ONLY MODELS
OPERA
TING LIMITS
L Maximum conditions
Outdoor temperature : 52°C D.B.*
Room temperature : 35°C D.B. / 22.5°C W.B.
L Minimum conditions
Outdoor temperature : 19°C D.B.**
Room temperature : 19°C D.B. / 14°C W.B.
L Model name CXXXL
* : 50°C D.B.
** : –15°C D.B.
HEAT PUMP MODELS
OPERA
TING LIMITS
L Cooling Maximum conditions
Outdoor temperature : 46°C D.B.
Room temperature : 35°C D.B. / 22°C W.B.
L Cooling Minimum conditions
Outdoor temperature : 19°C D.B.
Room temperature : 19°C D.B. / 14°C W.B.
L Heating Maximum conditions
Outdoor temperature : 24°C D.B. / 18°C W.B.
Room temperature : 27°C D.B.
L Heating Minimum conditions
Outdoor temperature : –8°C D.B. / –9°C W.B.
ACCESSORIES SUPPLIED WITH THE UNIT
PARTS FIGURE Q.TY PARTS FIGURE Q.TY
RAWL PLUG 7
PLASTIC
1
COVER
HEX
1
WRENCH
TAPPING
6
SCREW
REMOTE CONTROL
1
UNIT SCREW
AAAALKALINE
2
BATTERY
DRAIN
1
ELBOW
*
Power Supply:
The last digit(s) of the model number indicates the required
power supply to the unit.
5: 220 - 240 V ~ 50 Hz / 38: 380-400 V - 3N ~ 50 Hz
Last digit(s) of the model number
1. Standard screwdriver
2. Phillips head screwdriver
3. Knife or wire stripper
4. Tape measure
5. Level
6. Sabre saw or key hole saw
7. Hacksaw
8. Core bits ø 5
19. Hammer
10. Drill
11. Tube cutter
12. Tube flaring tool
13. Torque wrench
14. Adjustable wrench
15. Reamer (for reburring)
*
Available only for heat pump models.
Model Combinations
Combine indoor and outdoor units only as listed below.
COOLING ONLY MODELS R22
Indoor Units
Outdoor Units
SAP-KR165QS5 SAP-C165Q5
SAP-KR185QS5 SAP-C185Q5
SAP-C185QL5
SAP-C185Q38
SAP-C185QL38
SAP-KR225QS5 SAP-C225Q5
SAP-C225Q38
HEAT PUMP MODELS R22
Indoor Units
Outdoor Units
SAP-KR186QHS5 SAP-C186QH5
SAP-C186QH5N
SAP-C186QH38
SAP-C186QH38N
SAP-KR226QHS5 SAP-C226QH5
SAP-C226QH38
COOLING ONLY MODELS R407C
Indoor Units
Outdoor Units
SAP-KR165QS5 SAP-CR165G5
SAP-KR185QS5 SAP-CR185G5
SAP-CR185GL5
SAP-CR185G38
SAP-CR185GL38
SAP-KR225QS5 SAP-CR225G5
SAP-CR225G38
HEAT PUMP MODELS R407C
Indoor Units
Outdoor Units
SAP-KR186QHS5 SAP-CR186GH5N
SAP-CR186GH38N
SAP-KR226QHS5 SAP-CR226GH5
SAP-CR226GH38
EG
I
F
D
E
P
GR
©SANYO 2000
R407C MODELS: for the other installation works of CR models refer to
the “Installation Instructions” (green pages) on the top of the outdoor unit.
COOLING ONLY MODELS (R407C)
OPERA
TING LIMITS
L Maximum conditions
Outdoor temperature : 43°C D.B.
Room temperature : 32°C D.B. / 23°C W.B.
L Minimum conditions
Outdoor temperature : 19°C D.B.*
Room temperature : 19°C D.B. / 14°C W.B.
L Model name CXXXL
* : –15°C D.B.
Tools required for installation (not supplied)

Summary

Model Combinations and Operating Limits

Cooling Only Models R22

Heat Pump Models R22

Cooling Only Models R407 C

Heat Pump Models R407 C

Important Safety and Installation Guidelines

Pre-Installation Instructions

Emphasizes reading manual, following steps, and obeying codes.

Understanding Hazard Symbols

Explains warning symbols for injury, death, or property damage.

Electrical Wiring Safety

Details critical safety measures for electrical connections.

Indoor Unit Installation Procedures

Required Installation Space

Accessing and Connecting Unit Components

Indoor Unit Installation Steps

Drilling Holes and Preparing Panel Fixation

Securing the Rear Panel to the Wall

Lateral Tubing Connections

Electrical and Drain Connections

Connecting Power, Ground Wires, and Terminals

Installing the Condensate Drain

Outdoor Unit Installation Procedures and Requirements

Space, Base, and Mounting Preparations

Refrigerant Line Connections

Making Flare Connections

Tightening Connections

System Vacuum and Purging

Air Purging Procedure

Vacuum Pump Operation

Electrical Wiring Diagrams

1-Phase Model Wiring

Wiring diagrams for single-phase indoor and outdoor units.

3-Phase Model Wiring

Wiring diagrams for three-phase indoor and outdoor units.

Model-Specific Wiring Diagrams and Notes

Wiring Diagrams for 1-Phase and 3-Phase Models

Provides wiring diagrams for various models and important connection notes.

Test Run Procedures

Cooling Mode Test Run

Heating Mode Test Run

Refrigerant Pump Down Procedure

Step-by-Step Pump Down Process

Outdoor Unit Installation Considerations

Air Discharge Chamber Installation (C22 X;CR22 X Models)

Outdoor Unit Modifications for Specific Conditions

Baffle Plate Installation for Low Ambient;High Wind Conditions (CXXXL Models)

Outdoor Unit Installation for Specific Environments

Snow and Wind Protection for Heat Pump Models

Cooling Only Model Wiring Diagrams

Wiring Diagram: SAP-KR165 QS5; SAP-C165 Q5; SAP-CR165 G5

Electrical schematic for specific cooling only models.

Wiring Diagram: SAP-KR185 QS5; SAP-C185 Q5; SAP-CR185 G5

Electrical schematic for specific cooling only models.

Wiring Diagram: SAP-KR185 QS5; SAP-C185 QL5; SAP-CR185 GL5

Electrical schematic for specific cooling only models.

More Cooling Only Model Wiring Diagrams

Wiring Diagram: SAP-KR185 QS5; SAP-C185 Q38; SAP-CR185 G38

Electrical schematic for specific cooling only models.

Wiring Diagram: SAP-KR185 QS5; SAP-C185 QL38; SAP-CR185 GL38

Electrical schematic for specific cooling only models.

Wiring Diagram: SAP-KR225 QS5; SAP-C225 Q5; SAP-CR225 G5

Electrical schematic for specific cooling only models.

Final Cooling Only Model Wiring Diagram

Wiring Diagram: SAP-KR225 QS5; SAP-C225 Q38; SAP-CR225 G38

Electrical schematic for specific cooling only models.

Heat Pump Model Wiring Diagrams

Wiring Diagram: SAP-KR186 QHS5; SAP-C186 QH5; SAP-C186 QH5 N; SAP-CR186 GH5 N

Electrical schematic for heat pump models.

Wiring Diagram: SAP-C186 QH38; SAP-C186 QH38 N; SAP-CR186 GH38 N

Electrical schematic for heat pump models.

More Heat Pump Model Wiring Diagrams

Wiring Diagram: SAP-KR226 QHS5; SAP-C226 QH5; SAP-CR226 GH5

Electrical schematic for heat pump models.

Wiring Diagram: SAP-KR226 QHS5; SAP-C226 QH38; SAP-CR226 GH38

Electrical schematic for heat pump models.

Sanyo SAP-KR165QS5 Specifications

General

Capacity	1.5 Ton
Noise Level (Outdoor)	52 dB
Type	Split AC
Heating Capacity	Not Available
Power Supply	50 Hz
Coefficient of Performance (COP)	Not Available