iii
Adjusting the volume
Turn the VOLUME control or press the “+” or” -” VOL
switch on the remote controller.
While either of theVOL switches is being pressed, the
MOTOR DRIVEN CONTROL indicator will blink.
To reduce the volume temporarily (muting)
To reduce the volume level, press the MUTE (audio
muting) switch on the remote controller. [M] appears on
the tuner/timer display and the MOTOR DRIVEN CON-
TROL indicators blink.
The muting function will be retained for few days even if
the unit is turned off or the mains lead is disconnected.
The volume is restored to its previous level by pressing
the same switch again.
Adjusting the left/right speaker balance
Use the BALANCE control to adjust the left/right speaker
balance. Normally, it is kept at its centre position.
Adjusting the sound quality
By means of the 5 BAND GRAPHIC EQUALIZER controls
(100Hz/300Hz/l kHz/3kHz/12kHz), you can set your
favourite sound shape flexibly. Flat response is obtained
by setting the controls to the centre positions.
Selecting the function
The function is automatically selected when CD play or
tape playback has been started or when any of the
function switches (except the FM MODE switch) on the
tuner has been operated.
- When the function is switched, tape or CD play is
automatically stopped. (It is not stopped during tape
dubbing.)
- Press the PHONO or VIDEO function switch for turn-
table or video equipment operation.
Amplifier display
Indicates the input level and peak value of each sound
range.
General input level and peak value are indicated on
TOTAL.
Bass expander system
Press the BASSXPANDER switch to enhance the bass
sound.
Note:
Remember that the tape dubbing mode will be estab-
lished if the COMP. DUB switch is pressed when tapes
have been loaded in both deck 1 and deck 2.
Also remember that when CD has been selected as the
function and a tape has been loaded in deck 2, the CD
recording mode will be established when the COM-
PUTER REC switch is pressed.
COMPACT DISCS
Use compact discs bearing the symbol below. In addi-
tion to the conventional 12 cm CDs, this system can be
used to play 8 cm CDs without an adapter.
Im3iE
DIGITALAUDIO
Bear in mind the following points since any dirt, scratches
or warping of the discs can cause broken or intermittent
sound and also noise.
- To remove the disc from its case, lift it out by holding
the disc’s centre holder with your forefinger and the
outside of the disc with your thumb,
When holding the discs, take care not to touch the
playing surface (with the rainbow pattern).
Store the discs in their cases. Return them to their
cases with the label surface facing up and pushdown
lightly from above the label.
Do not place discs in the following locations:
Near a heating device or location where the tem-
perature is high.
Under no circumstances should discs be plac- ‘
on top of a seat or on the dashboard of a vehicm
whose windows are all closed and which is ex-
posed to direct sunlight since these areas can
become very hot indeed.
- In damp or dusty areas.
Do not write on the label surface using a ballpoint pen
or hard pencil, and do not stick labels on this surface,
either.
Wipe away any fingerprints or dust on the playing
surface of a disc using a soft cloth. Bear in mind the
following points.
Always wipe from the inside toward the outside of
the disc.
Do not use regular record cleaners, anti-static
agents, benzine, thinners or other solvents.
CD PLAY
Loading discs
1. Press the OPEN/CLOSE switch, The disc table is
extended halfivay.
2. Place the disc(s) with the label facing upon the disc
tray(s) (Fig. 10).
With an 8 cm disc, place the disc on the circular
section in the centre of the disc tray.
Do not place 8 cm and 12 cm discs on the same
disc tray.
Each time the DISC SKIP switch is pressed, the
carousel turns clockwise to the next tray position.
3, Press the OPEN/CLOSE switch again to retract the
disc table.
Note:
Do not put anything except a compact disc on the
tray, Foreign objects can damage the mechanism.
Do not touch the carousel while it is rotating.
-11-
To Next Page
Loading...
