What does B11 ERROR: RAM TEST FAILED mean on SATO Barcode Reader?
The SATO Barcode Reader displays 'B11 ERROR: RAM TEST FAILED' because the printer found a defactive memory location. Power off the printer for 15 seconds, then power on again. If the problem persists, contact an authorized customer service representative.
What does FILE SYS WRITE Check Flash mean on SATO GL412e Barcode Reader?
The SATO Barcode Reader shows 'FILE SYS WRITE' because there is a problem writing to flash memory. Power off the printer for 15 seconds, then power on again. If the problem persists, contact an authorized customer service representative.
How do I fix a B10 ERROR: NO DRAM DETECTED on my SATO GL412e Barcode Reader?
The SATO Barcode Reader shows 'B10 ERROR: NO DRAM DETECTED' because the printer could not find any DRAM. Power off the printer for 15 seconds, then power on again. If the problem persists, contact an authorized customer service representative.
Why does my SATO GL412e Barcode Reader say OPTION NOT INSTALLED?
The SATO Barcode Reader displays 'OPTION NOT INSTALLED' if the printer is powered on with the cutter enabled in the Media Handling menu, but the cutter itself is open (in the down position, or the cutter upper enclosure is removed) the printer cannot detect the cutter. When using the cutter, the printer must be powered on with the cutter in the up position and the cutter upper enclosure installed. Ensure the cutter option is installed, connected in the up position and the upper enclosure installed before powering on the printer. Install the cutter option or change to the correct Media Handling option in the MEDIA SETUP menu. If the error persists, contact an authorized customer service representative.
What does LABEL READY Remove Label mean on SATO GL412e Barcode Reader?
The SATO Barcode Reader displays 'LABEL READY' because a label was detected at the front of the printer by the Label Taken Sensor. This is the normal reminder message when Peel-Off or Tear-Off Media Handling has been selected. The incorrect Media Handling mode was selected. Remove the label from the front of the printer to allow the next label to print. Verify that a front door assembly is installed on the printer and that it is properly closed. Also ensure that debris is not obstructing the door mirror or the Label Taken Sensor. In the MEDIA SETUP menu, change Media Handling to the correct selection.
Why does my SATO GL412e show ERROR: INSUFFICIENT DRAM Cycle Power?
The SATO Barcode Reader displays 'ERROR: INSUFFICIENT DRAM' because not enough RAM memory is available for the printer to function. Power off the printer for 15 seconds, then power on again. If the message reappears, increase the Glob Mem Adjust size in the PRINTER SETUP menu and reboot the printer. If the message reappears, replace the main circuit board. Write down the message and return it with the defective board.
What should I do if my SATO GL412e displays PRINTHEAD POWER FAIL Cal For Service?
The SATO Barcode Reader shows 'PRINTHEAD POWER FAIL' because the print head lost power. Replace the print head. Power off the printer for 15 seconds, then power on again. If the problem persists, contact an authorized customer service representative.
What does PRINTHEAD HOT Wait 5 Minutes Go Online mean on SATO GL412e?
The SATO Barcode Reader displays 'PRINTHEAD HOT' because the print head has become overheated. Allow the print head to cool down for 5 minutes, then press the Pause key to resume printing. If possible, reduce print intensity. If the problem persists, contact an authorized customer service representative.
How to fix RIBBON OUT Load Ribbon error on SATO GL412e?
The SATO Barcode Reader indicates RIBBON OUT when the ribbon is broken between the ribbon rewind spindle and the print head or the ribbon supply is empty. To fix this, reattach the ribbon or load the printer with a new ribbon.
What causes GAP NOT DETECTED error on SATO GL412e Barcode Reader?
The SATO Barcode Reader displays 'GAP NOT DETECTED' because the printer is set for Gap or Mark sensing, but a black mark is not being detected. Ensure the Gap/Mark Sensor setting in the SENSOR SETUP menu matches the installed media. Ensure the sensors are properly positioned. Clean the sensor assembly and paper path. Run Auto-Cal to improve the sensor’s ability to detect the media in use. Run the Media Profile printout in the SENSOR SETUP menu. Run Manual Calibrate. Manually change the Gap/Mark Thresh and/or Paper Out Thresh values.
General| Brand | SATO |
|---|---|
| Model | GL412e |
| Category | Barcode Reader |
| Language | English |
To Next Page
