Scag Power Equipment Cheetah SCZ61V-27FX User Manual (English)

Questions and Answers:

K
Kevin MercadoAug 1, 2025
Why is my Scag Power Equipment Cheetah SCZ61V-27FX Lawn Mower leaving streaks of uncut grass in the cutting path?
- A
  Andrea OrtizAug 1, 2025
  If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass in the cutting path, several factors could be at play. The blades might be dull or worn, or perhaps they were sharpened incorrectly, so sharpen the blades. Ensure the engine is running at full RPM. Slipping belts could also be the culprit, so adjust the belt tension. Grass accumulation under the deck can cause this issue; therefore, clean the underside of the deck. Avoid mowing wet grass and slow down your ground speed. Bent blades can also cause this problem, so replace the blades.
R
robert64Aug 6, 2025
What to do if my Scag Power Equipment Cheetah SCZ61V-27FX leaves stringers of uncut grass?
- T
  tinapetersAug 6, 2025
  If your Scag Power Equipment Lawn Mower occasionally leaves blades of uncut grass, also known as stringers, it could be due to several reasons. Ensure the engine is running at full RPM. Adjust your ground speed to suit the conditions. Avoid cutting wet grass; wait until it has dried out. Sharpen the blades. Clean the underside of the deck to remove any grass accumulation. Finally, adjust the belt tension to prevent slipping.
F
foxbrookeAug 11, 2025
How to fix an uneven cut on flat ground with my Scag Power Equipment Lawn Mower?
- A
  Alan PenaAug 11, 2025
  If your Scag Power Equipment Lawn Mower is producing an uneven cut on flat ground, resulting in a wavy, high-low appearance, scalloped cut, or rough contour, consider these potential causes. If the lift is worn from the blade, replace the blade. Ensure the blade is mounted correctly with the cutting edge toward the ground. Clean the underside of the deck to remove any grass accumulation. Adjust the deck pitch and level. If the deck is mounted improperly or the spindle area is bent, consult your authorized SCAG dealer. Also, ensure that you sharpen the blade.
W
William Chan MDAug 16, 2025
Why does my Scag Power Equipment Cheetah SCZ61V-27FX leave a sloping ridge across the cutting path?
- C
  Cheryl RamirezAug 16, 2025
  If your Scag Power Equipment Lawn Mower is leaving a sloping ridge across the width of the cutting path, check and adjust the tire pressure to ensure it is equal on all tires. Also, ensure the wheels are even. If the deck is mounted incorrectly, consult your authorized SCAG dealer. Check if the deck is level side-to-side and correct if necessary.
M
Matthew ReynoldsAug 20, 2025
Why does my Scag Power Equipment Cheetah SCZ61V-27FX Lawn Mower leave strips of uncut grass between cutting paths?
- M
  Mary GarciaAug 21, 2025
  If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass between cutting paths, the issue is likely due to not enough overlapping between rows. Increase the overlap of each pass to resolve this.
A
Adam BradyAug 26, 2025
What causes an uneven cut on uneven ground with a Scag Power Equipment Lawn Mower?
- R
  Robin GeorgeAug 26, 2025
  If your Scag Power Equipment Lawn Mower is producing an uneven cut on uneven ground, resulting in a wavy appearance, high-low scalloped cut, or rough contour, it is likely due to the uneven ground itself. You may need to reduce ground speed, raise the cutting height, and/or change the direction of the cut.

Scag Power Equipment Cheetah SCZ61V-27FX Specifications

General

Engine Manufacturer	Kawasaki
Engine	FX Series
Engine Model	FX850V
Engine Power	27 hp
Fuel Type	Gasoline
Cutting Width	61 inches
Deck Type	Fabricated
Deck Material	Steel
Transmission	Hydro-Gear ZT-5400 Transaxles
Speed	Up to 16 mph
Fuel Capacity	12 gal
Weight	1430 lb
Cutting Height	1.5 - 5 inches