Scag Power Equipment V-Ride XL Series User Manual (English)

Questions and Answers:

K
Kyle GordonAug 13, 2025
How to fix occasional uncut grass blades with my Scag Power Equipment Lawn Mower?
- E
  Eric GoldenAug 13, 2025
  If you notice occasional blades of uncut grass, several factors could be at play. Ensure the engine is running at full RPM. Avoid cutting wet grass and allow it to dry out first. Sharpen the mower blades, and clean any grass accumulation from the underside of the deck. Also, check and adjust the belt tension if the belts are slipping. Reduce ground speed to adjust for conditions.
G
georgemurphyAug 17, 2025
Why is my Scag Power Equipment V-Ride XL leaving strips of uncut grass?
- D
  Debra PorterAug 17, 2025
  Strips of uncut grass can occur for several reasons. Make sure that the engine is running at full RPM. Sharpen dull or worn blades, ensuring correct sharpening. Adjust belt tension if it's slipping. Clean any grass buildup from the underside of the deck. Avoid cutting wet grass, and slow down if your ground speed is too fast. Replace bent blades.
N
Nicholas BrownAug 20, 2025
What to do if my Scag Power Equipment V-Ride XL Lawn Mower blades are scalping?
- N
  Nicholas WeberAug 20, 2025
  If your mower blades are hitting the dirt or cutting too close to the ground, check and adjust tire pressures. Reduce ground speed if it's too fast for the conditions. Consider raising the cutting height or changing the direction of your cut. If the terrain is rough, adjust your mowing approach accordingly. Avoid cutting wet grass.
U
uclarkAug 25, 2025
How to troubleshoot an uneven cut on flat ground with my Scag Power Equipment V-Ride XL Lawn Mower?
- D
  Don ZimmermanAug 25, 2025
  For an uneven cut on flat ground, start by replacing the blade if the lift is worn. Ensure the blade is mounted correctly with the cutting edge toward the ground. Clear any accumulated grass from the underside of the deck. Adjust the deck pitch and level if there's too much blade angle. Sharpen the blade if it's dull. If these steps don't resolve the issue, consult your authorized SCAG dealer, as the deck may be mounted improperly or the spindle area could be bent.
A
Angela RushAug 28, 2025
Why is my Scag Power Equipment V-Ride XL leaving a sloping ridge?
- W
  Whitney MarshAug 29, 2025
  A sloping ridge across the cutting path can be caused by unequal tire pressures. Check and adjust the tire pressure. Also, ensure the wheels are even. If the deck is not level from side to side, check and correct it. If these steps don't resolve the issue, consult your authorized SCAG dealer, as the deck may be mounted incorrectly.
S
Sean TurnerSep 1, 2025
What causes strips of uncut grass between cutting paths with my Scag Power Equipment V-Ride XL?
- R
  reynoldscarolineSep 1, 2025
  If you're seeing strips of uncut grass between cutting paths, it's likely that you're not overlapping enough between rows. Increase the overlap of each pass to ensure all grass is cut.
M
Melissa ContrerasSep 5, 2025
What to do for an uneven cut on uneven ground with my Scag Power Equipment V-Ride XL Lawn Mower?
- K
  Karen JarvisSep 5, 2025
  If you experience an uneven cut on uneven ground, it may be necessary to reduce ground speed, raise the cutting height, and/or change the direction of your cut.
L
Lisa CruzSep 8, 2025
How do I fix a step cut (ridge) in the center of the cutting path with my Scag Power Equipment V-Ride XL Lawn Mower?
- T
  Tony BlackSep 8, 2025
  A ridge in the center of the cutting path can be due to blades not mounted evenly. Adjust the pitch and level. Replace the blade if it is bent. If these steps don't resolve the issue, consult your authorized SCAG dealer, as there may be an internal spindle failure or incorrect spindle mounting.

Scag Power Equipment V-Ride XL Series Specifications

General

Spindle Material	Cast Iron
Cutting Width	52", 61"
Deck Construction	7-gauge steel
Horsepower Range	25-37 hp
Turning Radius	Zero
Standard Features	Suspension seat, hour meter

Summary

Section 1 General Information

1.1 Introduction

Overview of mower features, build quality, and manual usage instructions.

1.2 Direction Reference

Defines terminology like 'front,' 'rear,' 'left,' and 'right' relative to the operator's position.

1.3 Servicing Engine and Drive Train Components

Outlines service scope for engine & drivetrain, directing to dealers for warranty work.

1.4 Symbols

Explains various symbols used in the manual and on the machine for safety and operation.

Section 2 Safety Information

2.1 Introduction

Emphasizes operator safety, training, and the importance of adhering to manual instructions.

2.2 Signal Words

Defines DANGER, WARNING, and CAUTION signal words used in safety messages.

2.3 Before Operation Considerations

Lists crucial checks and safety points that must be addressed before starting the mower.

2.4 Testing the Safety Interlock System

Details procedures for testing the safety interlock functionality before each use.

2.5 Operation Considerations

Provides guidelines for safe and effective mower operation, including advice for slopes.

2.6 Maintenance Considerations and Storage

Outlines general maintenance practices and safe procedures for storing the mower.

2.7 Using a Spark Arrestor

Explains requirements and regulations for using spark arrestors, particularly in certain areas.

2.8 Spark Ignition System

States compliance with Canadian ICES-002 for the spark ignition system.

2.9 Safety and Instructional Decals

Illustrates and describes various safety decals found on the mower for user awareness.

Section 3 Specifications

3.1 Engine

Details engine specifications including type, displacement, cylinders, and idle speed.

3.2 Electrical

Lists electrical system components and their specifications.

3.3 Engine Deck

Describes the engine deck, drive system, steering, and wheel specifications.

3.4 Cutter Deck

Provides specifications for the cutter deck, including width, height adjustment, and blades.

3.5 Weights and Dimensions

Lists key physical dimensions and operating weights for different mower sizes.

3.6 Productivity

Estimates the mowing capacity in acres per day based on cutting width and speed.

Section 4 Operating Instructions

4.1 Tiger Eye Instrument Identification

Explains the function of each indicator light on the Tiger Eye monitoring system.

4.2 Controls Identification

Identifies and describes the purpose of various controls on the mower's operating panel.

4.3 Safety Interlock System & Testing

Explains the interlock system's function and provides steps to test its functionality.

4.5 Initial Run-in Procedures

Outlines checks and procedures for the first 20 hours of mower operation.

4.6 Starting the Engine

Details the correct procedure for starting the mower's engine.

4.7 Ground Travel and Steering

Guides the operator on safe and effective ground travel and steering techniques.

4.8 Engaging the Deck Drive (Cutter Blades)

Explains how to engage and disengage the mower deck blades.

4.9 Hillside Operation

Provides safety precautions and techniques for operating the mower on slopes.

4.10 Parking the Mower

Describes the procedure for safely parking the mower on a level surface.

4.11 After Operation

Lists cleaning and post-operation checks for the mower.

4.12 Removing Clogged Material

Instructs on safely clearing clogged discharge chutes using appropriate tools.

4.13 Moving Mower with Engine Stopped

Explains how to 'free-wheel' the mower for manual movement.

4.14 Recommendations for Mowing

Offers advice for optimal mowing performance and grass appearance.

4.15 Adjusting Cutting Height

Details the process for setting the desired cutting height of the mower deck.

4.16 Adjusting Cutting Height Range (High to Low)

Describes how to switch between the two available cutting height ranges.

Section 5 Troubleshooting Cutting Conditions

Section 6 Adjustments

6.1 Parking Brake Adjustment

Provides step-by-step instructions to adjust the parking brake for proper operation.

6.2 Travel Adjustment

Explains how to adjust the mower's tracking and neutral position for straight travel.

6.3 Throttle Control and Choke Adjustments

Directs users to consult authorized dealers for adjustments to throttle and choke controls.

6.4 Belt Adjustments

Advises on checking belt alignment, wear, and warns about pump drive belt failure.

6.5 Belt Alignment

Explains the importance of belt alignment and when to seek dealer assistance for wear issues.

6.6 Cutter Deck Adjustments

Details procedures for adjusting cutter deck level, pitch, and height for optimal cutting.

6.7 Electric Clutch Adjustment

Instructs on adjusting the air gap for the electric clutch for proper engagement and disengagement.

6.8 Operator Cushion and Rear Cover Removal

Explains how to remove the operator cushion and rear cover for maintenance access.

6.9 Adjusting the Operator Suspension Platform

Describes how to adjust ride comfort by altering the position of rubber isolators.

Section 7 Maintenance

7.10 Maintenance Chart - Recommended Service Intervals

A detailed chart outlining service tasks, recommended intervals, and relevant comments.

7.11 Lubrication

Provides a chart and diagrams for greasing fittings at specified intervals.

7.12 Hydraulic System

Covers procedures for checking and changing hydraulic oil levels and filters.

7.13 Engine Oil

Details procedures for checking and changing engine oil and oil filters.

7.14 Engine Fuel System

Explains safe fuel handling, filling procedures, and replacing the fuel filter.

7.15 Engine Air Cleaner

Describes how to clean or replace the engine air cleaner element.

7.16 Battery - Electric Start Models

Provides safety warnings and procedures related to the mower's battery.

7.17 Drive Belts

Outlines checking drive belts for alignment, wear, and replacement intervals.

7.18 Cutter Blades

Covers inspection, sharpening, and replacement procedures for mower blades.

7.19 Tires

Advises on checking tire pressure regularly for optimal performance.

7.20 Body and Deck

Provides instructions for washing, cleaning, and protecting the mower body and deck.

Section 8 Illustrated Parts List

8.1 Scag Approved Attachments and Accessories

Lists compatible attachments and accessories with their corresponding part numbers.

Limited Warranty - Commercial Equipment

Related product manuals

Scag Power Equipment V-ride

2 pages

Scag Power Equipment V-Ride II

91 pages

Scag Power Equipment SMTC-48V

28 pages

Scag Power Equipment SW36-13KH