Scag Power Equipment V-RIDE SVR61V-29FX User Manual (English)

Questions and Answers:

L
Luis KingAug 13, 2025
Why is my Scag Power Equipment Lawn Mower streaking and leaving strips of uncut grass?
- J
  James EnglishAug 13, 2025
  Your Scag Power Equipment Lawn Mower may be streaking due to several reasons: dull or worn blades, which require sharpening; incorrect blade sharpening, also requiring you to sharpen the blades; low engine RPM, so run the engine at full RPM; a slipping belt, which means you should adjust the belt tension; a deck plugged with grass accumulation, so clean the underside of the deck; ground speed being too fast, so slow your speed to adjust for conditions; wet grass, so cut the grass after it has dried out; or bent blades, which means you should replace the blades.
J
Jason StevensAug 16, 2025
What to do if my Scag Power Equipment V-RIDE SVR61V-29FX Lawn Mower blades are hitting dirt or cutting too close to the ground (scalping)?
- T
  Theresa ArellanoAug 16, 2025
  If your Scag Power Equipment Lawn Mower is scalping, it could be due to several factors. Check and adjust low tire pressures. If your ground speed is too fast, slow down to adjust for conditions. If you are cutting too low, you may need to reduce ground speed, raise the cutting height, change the direction of cut, and/or change the pitch and level. Rough terrain may also be the cause, so you may need to reduce ground speed, raise the cutting height, and/or change the direction of cut. Cutting wet grass can also cause scalping, so cut the grass after it has dried out.
D
Donna StephensAug 20, 2025
How to fix stringers (occasional blades of uncut grass) with my Scag Power Equipment V-RIDE SVR61V-29FX Lawn Mower?
- K
  katherineleachAug 20, 2025
  If your Scag Power Equipment Lawn Mower is leaving occasional blades of uncut grass, it could be due to low engine RPM, so run the engine at full RPM. If your ground speed is too fast, slow down to adjust for conditions. Wet grass can also cause this issue, so cut the grass after it has dried out. Other causes include dull blades, which require sharpening; a deck plugged with grass accumulation, so clean the underside of the deck; or belts slipping, so adjust the belt tension.
A
Ashley NielsenAug 25, 2025
Why is my Scag Power Equipment V-RIDE SVR61V-29FX Lawn Mower leaving an uneven cut on flat ground?
- A
  acannonAug 25, 2025
  An uneven cut on flat ground with your Scag Power Equipment Lawn Mower can occur for several reasons. The lift may be worn from the blade, so replace the blade. Ensure the blade is not upside down; mount it with the cutting edge toward the ground. A deck plugged with grass accumulation can also cause this, so clean the underside of the deck. Too much blade angle (deck pitch) can be a factor, so adjust the pitch and level. If the deck is mounted improperly or the spindle area is bent, see your authorized SCAG dealer. A dull blade can also cause an uneven cut, so sharpen the blade.
D
Darren MaloneAug 28, 2025
How to correct a sloping ridge across the cutting path of my Scag Power Equipment V-RIDE SVR61V-29FX Lawn Mower?
- T
  Thomas RobertsonAug 28, 2025
  A sloping ridge across the cutting path of your Scag Power Equipment Lawn Mower can be caused by unequal tire pressures, so check and adjust the tire pressure. Uneven wheels can also cause this, so check and adjust the tire pressure. If the deck is mounted incorrectly, see your authorized SCAG dealer. Also, the deck may not be level side-to-side, so check for level and correct it.
N
Nancy GomezAug 31, 2025
What causes a step cut (ridge in center of cutting path) with a Scag Power Equipment V-RIDE SVR61V-29FX?
- S
  Sharon RoweAug 31, 2025
  A step cut with your Scag Power Equipment Lawn Mower may be due to blades not mounted evenly, so adjust the pitch and level. A bent blade can also cause this, so replace the blade. For internal spindle failure or incorrect mounting of the spindle, see your authorized SCAG dealer.
B
Benjamin StaffordSep 4, 2025
Why is my Scag Power Equipment Lawn Mower leaving an uneven cut on uneven ground?
- J
  Jennifer GonzalezSep 4, 2025
  If your Scag Power Equipment Lawn Mower is leaving an uneven cut on uneven ground, it's likely due to the uneven ground itself. You may need to reduce ground speed, raise the cutting height, and/or change the direction of cut.
X
xhinesSep 8, 2025
Why is my Scag Power Equipment Lawn Mower streaking and leaving strips of uncut grass between cutting paths?
- H
  Heidi RobinsonSep 8, 2025
  If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass between cutting paths, it is because there is not enough overlapping between rows. Increase the overlap of each pass to resolve this.

Scag Power Equipment V-RIDE SVR61V-29FX Specifications

General

Category	Lawn Mower
Manufacturer	Scag Power Equipment
Model	V-RIDE SVR61V-29FX
Engine	Kawasaki FX850V
Engine Model	FX850V
Fuel Type	Gasoline
Engine Displacement	852 cc
Horsepower	29 hp
Cutting Width	61 inches
Deck Type	Fabricated
Transmission	Hydrostatic
Turning Radius	Zero Turn
Speed	10 mph
Blade Engagement	Electric
Tire Size Front	13 x 6.5-6

Summary

General Information

Introduction

Overview of the mower's purpose and guidance on using the manual effectively.

Direction Reference

Defines directional terms like left, right, front, and rear relative to the operator.

Servicing Engine and Drivetrain Components

Outlines the manual's scope for engine/drivetrain service and directs users to dealers.

Symbols

Explains graphical symbols and their meanings used throughout the manual.

Safety Information

Introduction

Emphasizes the operator's role in safety and the necessity of proper training.

Signal Words

Defines signal words (DANGER, WARNING, CAUTION) and the hazard alert symbol.

Before Operation Considerations

Lists critical checks and precautions required before operating the mower.

Operation Considerations

Key safety and procedural guidelines essential for operating the mower safely.

Maintenance Considerations & Storage

Important safety points for maintenance, repairs, and proper storage of the equipment.

Using a Spark Arrestor

Discusses requirements and regulations concerning spark arrestors in specific areas.

Safety and Instructional Decals

Identifies and explains the purpose of various safety and instructional decals on the machine.

Specifications

Engine

Details engine type, horsepower, cylinders, governor, and fuel specifications.

Electrical

Lists starter type, interlock switches, and instrument panel components.

Engine Deck

Describes the drive system, pumps, motors, steering, and brake components.

Cutter Deck

Specifies deck type, construction, cutting width, blade details, and discharge.

Weights and Dimensions

Provides physical measurements and operating weight for the mower.

Productivity

Estimates acres mowed per day based on cutting width and speed.

Operating Instructions

Controls and Instruments

Identifies and explains the function of all mower and engine controls and instruments.

Safety Interlock System

Explains the interlock system designed to prevent unsafe operation.

Initial Run-in Procedures

Outlines required checks and services for the first 20 hours of operation.

Starting the Engine

Step-by-step guide for safely starting the mower's engine.

Ground Travel and Steering

Detailed instructions for operating the mower's forward and reverse travel and steering.

Engaging Deck Drive

Explains how to engage and disengage the mower deck drive system.

Hillside Operation

Specific safety precautions and operating techniques for mowing on slopes.

Parking the Mower

Steps for safely parking the mower on a level surface.

After Operation

Procedures for cleaning and basic checks after completing mowing.

Removing Clogged Material

Safety instructions for clearing blockages in the discharge chute.

Moving Mower with Engine Stopped

How to move the mower when the engine is not running.

Mowing Recommendations

Tips for achieving optimal mowing results and lawn appearance.

Adjusting Cutting Height

Step-by-step guide for setting the desired cutting height of the mower deck.

Troubleshooting Cutting Conditions

Adjustments

Parking Brake Adjustment

Step-by-step guide for adjusting the parking brake linkage for proper function.

Travel Adjustment

Procedures for adjusting neutral and tracking for accurate mower movement.

Neutral Adjustment

Procedure to adjust the mower's neutral position to prevent creeping.

Tracking Adjustment

Procedure to adjust steering controls for straight forward travel.

Throttle and Choke Adjustments

Notes that engine adjustments require dealer service for optimal performance.

Belt Adjustments

Mentions self-tensioning belts and the need for periodic checks for alignment and wear.

Belt Alignment

Highlights belt alignment importance and directs to dealer for wear/breakage issues.

Cutter Deck Level

Instructions for ensuring the mower deck is level side-to-side.

Cutter Deck Pitch

Instructions for setting the correct front-to-rear pitch of the mower deck.

Cutter Deck Height

Detailed steps for adjusting the mower deck's cutting height.

Custom-Cut Baffle Adjustment

Guide to adjusting the baffle for different cutting conditions and grass types.

Electric Clutch Adjustment

Procedure to adjust the air gap on the electric clutch for proper operation.

Front Weight Adjustment

Information on standard and optional weights for the front of the machine.

Operator Cushion Adjustment

Instructions for mounting the operator cushion for different operator sizes.

Maintenance

Maintenance Chart

Provides a schedule of maintenance tasks based on operating hours.

Lubrication

Details lubrication points, intervals, and types of lubricants required.

Hydraulic System

Covers checking and changing hydraulic oil level, filter, and system.

Engine Oil

Instructions for checking and changing engine oil and oil filter.

Engine Fuel System

Procedures for filling the fuel tank and replacing the fuel filter.

Engine Air Cleaner

Guidance on cleaning and replacing the air cleaner element.

Battery

Safety warnings and instructions for charging and handling the battery.

Cutter Blades

Procedures for blade inspection, sharpening, and replacement.

Tires

Specifies tire pressure checks for caster and drive wheels.

Body and Deck

Recommendations for washing and maintaining the mower's body and deck.

Illustrated Parts List

Approved Attachments and Accessories

Lists attachments and accessories approved for use with the mower.

61V Cutter Deck

SVR-61V Cutter Deck Controls

SVR-61V Sheet Metal Components

SVR-61V Steering Controls

SVR-61V Fuel System - EPA Phase 2

SVR-61V Fuel System - EPA Phase 3

SVR-61V Hydraulics and Engine Components

SVR Electrical Schematic

Replacement Decals and Information Plates

Limited Warranty - Commercial Equipment

Related product manuals

V-Ride SVR52V-730FX

74 pages

Scag Power Equipment V-ride

2 pages

Scag Power Equipment V-Ride II

91 pages

V-Ride XL Series

75 pages

Scag Power Equipment SM-61

25 pages

Scag Power Equipment SMWC-52V

34 pages

Scag Power Equipment SMTC-48V

Turf Tiger STT-31EFI-SS

116 pages

Turf Tiger Propane STT52V-25CH-LP

76 pages

Scag Power Equipment V-RIDE SVR61V-29FX User Manual

Table of Contents

Questions and Answers:

Scag Power Equipment V-RIDE SVR61V-29FX Specifications

Summary

General Information

Introduction

Direction Reference

Servicing Engine and Drivetrain Components

Symbols

Safety Information

Introduction

Signal Words

Before Operation Considerations

Operation Considerations

Maintenance Considerations & Storage

Using a Spark Arrestor

Safety and Instructional Decals

Specifications

Engine

Electrical

Engine Deck

Cutter Deck

Weights and Dimensions

Productivity

Operating Instructions

Controls and Instruments

Safety Interlock System

Initial Run-in Procedures

Starting the Engine

Ground Travel and Steering

Engaging Deck Drive

Hillside Operation

Parking the Mower

After Operation

Removing Clogged Material

Moving Mower with Engine Stopped

Mowing Recommendations

Adjusting Cutting Height

Troubleshooting Cutting Conditions

Adjustments

Parking Brake Adjustment

Travel Adjustment

Neutral Adjustment

Tracking Adjustment

Throttle and Choke Adjustments

Belt Adjustments

Belt Alignment

Cutter Deck Level

Cutter Deck Pitch

Cutter Deck Height

Custom-Cut Baffle Adjustment

Electric Clutch Adjustment

Front Weight Adjustment

Operator Cushion Adjustment

Maintenance

Maintenance Chart

Lubrication

Hydraulic System

Engine Oil

Engine Fuel System

Engine Air Cleaner

Battery

Cutter Blades

Tires

Body and Deck

Illustrated Parts List

Approved Attachments and Accessories

61V Cutter Deck

SVR-61V Cutter Deck Controls

SVR-61V Sheet Metal Components

SVR-61V Steering Controls

SVR-61V Fuel System - EPA Phase 2

SVR-61V Fuel System - EPA Phase 3

SVR-61V Hydraulics and Engine Components

SVR Electrical Schematic

Replacement Decals and Information Plates

Limited Warranty - Commercial Equipment

Related product manuals