Scag Power Equipment V-Ride SVR52V-730FX User Manual (English)

Questions and Answers:

P
philipfischerJul 29, 2025
Why is my Scag Power Equipment V-Ride SVR52V-730FX leaving strips of uncut grass?
- B
  Beth ZamoraJul 29, 2025
  If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass in the cutting path, several factors could be responsible. The blades may be dull or worn and require sharpening. Ensure you are running the engine at full RPM. The belt might be slipping, so adjust the belt tension. Also, grass accumulation under the deck can cause this, so clean the underside of the deck. Ground speed could be too fast, so reduce speed. Cutting wet grass can also cause this issue, so allow the grass to dry. Finally, check for bent blades and replace them if necessary.
Y
yallenAug 2, 2025
How to fix occasional blades of uncut grass with my Scag Power Equipment Lawn Mower?
- J
  Jennifer WagnerAug 2, 2025
  If your Scag Power Equipment Lawn Mower is leaving occasional blades of uncut grass, there are several possible causes. Ensure the engine is running at full RPM. If your ground speed is too fast, slow down. Cutting wet grass can cause this, so cut after it has dried. Dull blades or incorrect sharpening can be a factor, so sharpen the blades. Also, grass accumulation under the deck can cause this, so clean the underside of the deck. Finally, check for belts slipping and adjust the belt tension if needed.
G
gentryphillipAug 7, 2025
Why is my Scag Power Equipment V-Ride SVR52V-730FX Lawn Mower cutting unevenly on flat ground?
- K
  kruizAug 7, 2025
  If your Scag Power Equipment Lawn Mower is producing an uneven cut on flat ground, resulting in a wavy, high-low appearance, scalloped cut, or rough contour, several factors could be responsible. If the lift is worn from the blade, replace the blade. Ensure the blade is mounted with the cutting edge toward the ground. Clean any grass accumulation from the underside of the deck. Adjust the deck pitch and level if there's too much blade angle. If the deck is mounted improperly or the spindle area is bent, consult your authorized SCAG dealer for assistance. Finally, a dull blade can cause this issue, so sharpen the blade.
R
rwilkersonAug 10, 2025
How to prevent strips of uncut grass between cutting paths with my Scag Power Equipment Lawn Mower?
- B
  Brent DillonAug 11, 2025
  If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass between cutting paths, increase the overlap of each pass.
C
Carolyn MoodyAug 15, 2025
Why does my Scag Power Equipment V-Ride SVR52V-730FX Lawn Mower leave a sloping ridge across the cutting path?
- R
  Renee GatesAug 16, 2025
  If your Scag Power Equipment Lawn Mower is leaving a sloping ridge across the width of the cutting path, check and adjust the tire pressure to ensure they are equal. Also, check and adjust the tire pressure if the wheels are uneven. If the deck is mounted incorrectly or is not level side to side, consult your authorized SCAG dealer, and check for level and correct it.
P
Patrick CoxAug 19, 2025
What to do if my Scag Power Equipment V-Ride SVR52V-730FX is scalping?
- K
  Kenneth PetersonAug 20, 2025
  If your Scag Power Equipment Lawn Mower blades are hitting the dirt or cutting too close to the ground, check and adjust the tire pressures. Reduce ground speed if it's too fast. If you are cutting too low, you may need to reduce ground speed, raise the cutting height, change the direction of cut, and/or change the pitch and level. These issues can also arise on rough terrain, so consider reducing speed, raising the cutting height, and/or changing the direction of cut. Cutting wet grass can also cause scalping, so allow the grass to dry before cutting.
J
jtuckerAug 23, 2025
What to do if my Scag Power Equipment V-Ride SVR52V-730FX Lawn Mower leaves a ridge in the center of the cutting path?
- A
  Austin MooreAug 25, 2025
  If your Scag Power Equipment Lawn Mower is leaving a ridge in the center of the cutting path, the blades may not be mounted evenly, so adjust the pitch and level. Alternatively, the blade could be bent, so replace the blade. For internal spindle failure or incorrect mounting of the spindle, consult your authorized SCAG dealer.

Scag Power Equipment V-Ride SVR52V-730FX Specifications

General

Category	Lawn Mower
Manufacturer	Scag Power Equipment
Model	V-Ride SVR52V-730FX
Engine	Kawasaki FX730V
Engine Displacement	726 cc
Cutting Width	52 inches
Deck Type	Fabricated
Spindle Material	Cast Iron
Cutting Height Range	1.5 - 5 inches
Turning Radius	Zero Turn
Transmission	Hydro-Gear ZT-3400
Weight	1190 lbs
Wheel Size - Front	13 x 6.5 inches