Scansonic DA310 - FM Radio Operation; FM Tuning Modes

16
DLS (Dynamic Label Segment)
Dynamic label segment is a scrolling message that the broadcaster may
include with their transmissions. The message usually includes information,
such as programme details etc.
Programme Type
This describes the “style” or “genre” of the programme that is being broad-
cast.
Audio Bit Rate
The display will show the digital audio bit rate being received.
Frequency
This displays the frequency of the present station, such as “11C
220.352MHz”.
FM operation
Switching from DAB to FM mode
To switch the unit to FM mode, press MODE repeatedly to select FM mode.
The display will show the frequency.
Auto scan
Press SCAN/►/II until the tuner starts searching for a station. To scan
down the frequency band, press and hold SCAN/►/II. Once a station has
been found, the scanning will stop automatically.
Manual scan
To search for FM stations manually, press I◄◄ I ►► repeatedly until your
desired frequency is reached.
Audio mode
Press SELECT/MONO/ST. on the remote control to toggle between the
Stereo or Mono selection.
The search may not stop at a station with a very weak signal.
general operation
powering ON/OFF
Scan Time
00:00:00” and synchronize to the current local time if you can receive a DAB signal in your
location. After approximate one minute, it will switch to STANDBY mode.
t Press on the unit or press ON/STAND-BY on the remote control to switch the unit to
ON mode.
t Press to switch the unit back to STANDBY mode.
t
completely.
t When the unit is idle for approximately 15 minutes, it will automatically switch to standby.
t
selecting modes
Press MODE repeatedly to switch between DAB, FM, CD, USB, AUX and Bluetooth modes.
adjusting the volume
t Turn the VOLUME +/– dial on the unit or press VOLUME +/– on the remote control to
adjust the volume.
t
MUTE on the remote control. Press MUTE again
or press VOLUME +/– on the remote control or turn VOLUME +/– to resume normal
listening.
auto setting the clock
The clock can be updated automatically if you can receive a DAB signal in your location.
In order to synchronise to the current local time you must leave it on the DAB station for a
short period of time.
manually setting the time
1. During Standby mode, press and hold CLOCK on the remote control. The hour digits
2. Press to adjust the hour digits, and then press CLOCK
3. Press to adjust the minute digits, and then press CLOCK
4. The time is now set.
15
MODE repeatedly on the unit or press
CD, USB, TUNER/DAB, AUDIO IN,
BLUETOOTH on the remote
general operation
powering ON/OFF
Scan Time
00:00:00” and synchronize to the current local time if you can receive a DAB signal in your
location. After approximate one minute, it will switch to STANDBY mode.
t Press on the unit or press ON/STAND-BY on the remote control to switch the unit to
ON mode.
t Press to switch the unit back to STANDBY mode.
t
completely.
t When the unit is idle for approximately 15 minutes, it will automatically switch to standby.
t
selecting modes
Press MODE repeatedly to switch between DAB, FM, CD, USB, AUX and Bluetooth modes.
adjusting the volume
t Turn the VOLUME +/– dial on the unit or press VOLUME +/– on the remote control to
adjust the volume.
t
MUTE on the remote control. Press MUTE again
or press VOLUME +/– on the remote control or turn VOLUME +/– to resume normal
listening.
auto setting the clock
The clock can be updated automatically if you can receive a DAB signal in your location.
In order to synchronise to the current local time you must leave it on the DAB station for a
short period of time.
manually setting the time
1. During Standby mode, press and hold CLOCK on the remote control. The hour digits
2. Press to adjust the hour digits, and then press CLOCK
3. Press to adjust the minute digits, and then press CLOCK
4. The time is now set.
15
MODE repeatedly on the unit or press
CD, USB, TUNER/DAB, AUDIO IN,
BLUETOOTH on the remote
With FM radio it may be necessary to ne tune each station by
pressing I◄◄ I ►► repeatedly. Each press/tap will adjust the
frequency by 0.05MHz. If reception is still poor adjust the position of
the aerial or try moving the radio to another location.