Scansonic DA310 - Page 17

17
Preset stations
You can store up to 30 of your favourite stations to the memory. This will
enable you to access your favourite stations quickly and easily.
1. Tostoreapreset,youmustrstbelisteningtothestationthatyouwould
like to save, press and hold MEMORY. The display will show “Preset
Store <#: (Empty)>”.
2. Press PRESET to select your desired preset station number.Then
pressENTERconrm.
3. The station will be stored in few seconds and the screen will then show
“Preset # Stored“.
Recalling a stored station
1. Once you have saved a station to one of the preset buttons, you can
recall it by pressing MEMORY.
2. Press PRESET until your desired station show on the display; Then
pressENTERconrm.
FM display modes
Press DISPLAY on the remote control, the display will switch through the
following display modes.
The information of each display mode is displayed on the lower segment of
the display.
Radio Text
This is a scrolling message displaying information
about the current programme.
Programme Type
This describes the “style” or “genre” of the
programme that is being broadcast.
general operation
powering ON/OFF
Scan Time
00:00:00” and synchronize to the current local time if you can receive a DAB signal in your
location. After approximate one minute, it will switch to STANDBY mode.
t Press on the unit or press ON/STAND-BY on the remote control to switch the unit to
ON mode.
t Press to switch the unit back to STANDBY mode.
t
completely.
t When the unit is idle for approximately 15 minutes, it will automatically switch to standby.
t
selecting modes
Press MODE repeatedly to switch between DAB, FM, CD, USB, AUX and Bluetooth modes.
adjusting the volume
t Turn the VOLUME +/– dial on the unit or press VOLUME +/– on the remote control to
adjust the volume.
t
MUTE on the remote control. Press MUTE again
or press VOLUME +/– on the remote control or turn VOLUME +/– to resume normal
listening.
auto setting the clock
The clock can be updated automatically if you can receive a DAB signal in your location.
In order to synchronise to the current local time you must leave it on the DAB station for a
short period of time.
manually setting the time
1. During Standby mode, press and hold CLOCK on the remote control. The hour digits
2. Press to adjust the hour digits, and then press CLOCK
3. Press to adjust the minute digits, and then press CLOCK
4. The time is now set.
15
MODE repeatedly on the unit or press
CD, USB, TUNER/DAB, AUDIO IN,
BLUETOOTH on the remote
The unit will automatically switch between stereo and mono mode,
but you can override this and switch this function manually. This is
helpful when receiving poor signal reception.
general operation
powering ON/OFF
Scan Time
00:00:00” and synchronize to the current local time if you can receive a DAB signal in your
location. After approximate one minute, it will switch to STANDBY mode.
t Press on the unit or press ON/STAND-BY on the remote control to switch the unit to
ON mode.
t Press to switch the unit back to STANDBY mode.
t
completely.
t When the unit is idle for approximately 15 minutes, it will automatically switch to standby.
t
selecting modes
Press MODE repeatedly to switch between DAB, FM, CD, USB, AUX and Bluetooth modes.
adjusting the volume
t Turn the VOLUME +/– dial on the unit or press VOLUME +/– on the remote control to
adjust the volume.
t
MUTE on the remote control. Press MUTE again
or press VOLUME +/– on the remote control or turn VOLUME +/– to resume normal
listening.
auto setting the clock
The clock can be updated automatically if you can receive a DAB signal in your location.
In order to synchronise to the current local time you must leave it on the DAB station for a
short period of time.
manually setting the time
1. During Standby mode, press and hold CLOCK on the remote control. The hour digits
2. Press to adjust the hour digits, and then press CLOCK
3. Press to adjust the minute digits, and then press CLOCK
4. The time is now set.
15
MODE repeatedly on the unit or press
CD, USB, TUNER/DAB, AUDIO IN,
BLUETOOTH on the remote
The stored stations will be saved into the memory and power off will
not erase it. Storing a new staion into a preset location will erase
the previously station in that location.
recalling a stored station
1. Once you have saved a station to one of the preset buttons, you can recall it by pressing
MEMORY.
2. Press PRESET until your desired station show on the display; Then press ENTER
conrm.
a new station into a preset location will erase the previously stored station in that location.
FM display modes
Press DISPLAY on the remote control, the display will switch through the following display
modes.
The information of each display mode is displayed on the lower segment of the display.
Radio Text
This is a scrolling message displaying information
about the current programme.
Programme Type
This describes the “style” or “genre” of the
programme that is being broadcast.
Station Name
This displays the station name.
Audio Type
This displays if the station being received is in mono
or stereo.
Radio Text
Programme Type
Station Name
Audio Type
22