To Next PageTo Next Page
Why excessive drill bit run-out or wobble with Scheppach DP16VLS?
If you're experiencing excessive drill bit run-out or wobble with your Scheppach Drill, there are several possible causes. It could be due to a bent drill bit (use a straight one), worn spindle bearings (replace them), the drill bit not being clamped centrally in the chuck (check the centering), or the chuck not being properly installed (install it correctly).
How to fix a noisy Scheppach Power Tool?
Noisy operation of your Scheppach Power Tool can be caused by: * Incorrect belt tension. Adjust the belt tension. * Dry spindle. Test the spindle. * Loose spindle pulley. Check the retaining nut on the pulley and tighten if necessary. * Loose motor pulley. Tighten the set screw in the motor pulley.
Why is the hole not round when using my Scheppach Power Tool?
If the drill leads off or the hole is not round when using your Scheppach Power Tool, it could be due to: * Hard grain in the wood or unequal lips and/or angle. Resharpen the drill bit. * A bent drill bit. Replace the drill bit.
How to fix excessive drill bit run-out on Scheppach Power Tool?
Excessive drill bit run-out or wobble in your Scheppach Power Tool can be caused by: * A bent drill bit. Use a straight drill bit. * Worn spindle bearings. Replace the bearings. * The drill bit not being clamped centrally in the chuck. Check the centering of the drill. * The chuck not being properly installed. Properly install the chuck.
What to do if drill bit binds in workpiece of Scheppach Power Tool?
If the drill bit binds in the workpiece when using your Scheppach Power Tool, it could be due to: * The workpiece pinching the drill bit or excessive feed pressure. Support or clamp the workpiece. * Improper belt tension. Adjust the belt tension.
Why is there excessive drill bit run-out or wobble on my Scheppach Drill?
If you experience excessive drill bit run-out or wobble with your Scheppach Drill, consider these potential causes and solutions: * **Bent drill bit:** Use a straight drill bit. * **Worn spindle bearings:** Replace the bearings. * **Drill bit not clamped centrally in chuck:** Check the centering of the drill. * **Chuck not properly installed:** Properly install the chuck.
What to do if the Scheppach DP16VLS Drill workpiece is torn loose from hand?
If the Scheppach Drill workpiece is torn loose from your hand, you should support or clamp the workpiece.
What to do if the Scheppach Drill bit binds in the workpiece?
If the Scheppach Drill bit binds in the workpiece, it might be due to the workpiece pinching or excessive feed pressure. Support or clamp the workpiece. Also, adjust the belt tension.
Why does my Scheppach DP16VLS Drill bit bind in the workpiece?
A drill bit binding in the workpiece with your Scheppach Drill can occur because: 1. The workpiece is pinching due to feed pressure, so support the workpiece or clamp it. 2. The belt tension is improper, so adjust the belt tension.
How to fix a noisy Scheppach Drill?
A noisy Scheppach Drill can be caused by several factors: 1. Incorrect belt tension, which requires adjustment. 2. A dry spindle, which needs lubrication. 3. A loose spindle pulley, so check the retaining nut and tighten if necessary. 4. A loose motor pulley, which requires tightening the set screw.
General| Drilling | Yes |
|---|---|
| Screwdriving | - |
| Product color | Blue, Grey |
| Input power | 500 W |
| Power source | AC |
| AC input voltage | 230 - 240 V |
| AC input frequency | 50 Hz |
| Idle speed (max) | - RPM |
| Chuck capacity (max) | 16 mm |
| Drilling diameter in steel (max) | - mm |
| Product type | Bench drill press |
| Housing material | Steel |
| Drill table size (WxD) | 160 x 160 mm |
Weight and Dimensions| Depth | 460 mm |
|---|---|
| Width | 380 mm |
| Height | 250 mm |
| Weight | 15420 g |
