23GB
The drill speeds specifi ed are merely suggested values.
Drill
bit Ø
Cast
iron
Steel Iron Alumin-
ium
Bronze
3 2550 1600 2230 9500 8000
4 1900 1200 1680 7200 6000
5 1530 955 1340 5700 4800
6 1270 800 1100 4800 4000
7 1090 680 960 4100 3400
8 960 600 840 3600 3000
9 850 530 740 3200 2650
10 765 480 670 2860 2400
11 700 435 610 2600 2170
12 640 400 560 2400 2000
13 590 370 515 2200 1840
14 545 340 480 2000 1700
16 480 300 420 1800 1500
Countersinking and center-drilling
With this table drill, you can also countersink and center-drill.
Please observe that countersinking should be performed at the
lowest speed, while a high speed is required for center-drilling.
Drilling wood
Please note that sawdust must be properly evacuated when
working with wood, as it can pose a health hazard. Ensure
that you wear a suitable dust mask when performing work that
generates dust.
11. Transport
The machine may only be lifted and transported on the belt box
and on the frame plate. Never lift it by the guards or adjusting
handles for transport.
For transport, the machine must be disconnected from the
mains.
12. Cleaning and Servicing
Pull the mains plug before any adjustments, main-
tenance or repair.
m Have any work on the device that is not de-
scribed in this instruction guide performed by a
professional. Only use original parts. Allow the
device to cool off before any maintenance or clean-
ing is undertaken.
There is a risk of burning!
Always check the device before using it for obvious defects
such as loose, worn or damaged parts, correct the positioning
of screws or other parts. Exchange the damaged parts.
• Do not use any cleaning agents or solvents. Chemical sub-
stances can etch the plastic parts of the device. Never clean
the device under running water.
• Thoroughly clean the device after every use.
• Clean the ventilation openings and the surface of the device
with a soft brush or cloth.
• Remove chips, dust and dirt with a vacuum cleaner if neces-
sary.
• Lubricate moving parts regularly.
• Do not allow lubricants to come into contact with switches,
V-belts, pulleys and drill lifting arms.
WARNING:
Always unplug our tool from power source before any adjust-
ment“
Setting the laser (Fig.15+16)
The laser (13) forms a crosshair in the centre of the drill. If the
laser line does not meet in the centre of the drill, the laser must
be adjusted.
The laser can be adjusted via the adjusting screws (T)
Clamp a drill bit in the chuck (5).
Position the drilling table (3) as close as possible to the drill.
Loosen the locknuts (W).
It is possible to adjust the laser lines by turning the adjustment
screws (T).
Set the laser lines such that they cross in the middle of the drill
tip.
Adjusting the spindle retaining spring (Fig.9)
It may be necessary for the spindle retaining spring to be ad-
justed because of changed tension, making the spindle return
too quickly or too slowly.
1. To provide more space, lower the table.
2. Work on the left side of the drill.
3. Put a screwdriver in the front lower notch (L), keeping it
in place.
4. Remove the outer locknut (O) with a flat spanner (SW16).
5. Leaving the screwdriver in the notch, loosen the inner
locknut (N) until the cut-out is released from the boss (P).
WARNING! Spring is under tension!
6. Using the screwdriver, carefully turn the spring cap (M) an-
ti-clockwise until you can press the notch into the boss (P).
7. Lower the spindle to the lowest position and hold the
spring cap (M) in place. When the spindle moves up and
down as desired, retighten the inner locknut (N).
8. If it is too loose, repeat steps 3-5. If it is too tight, repeat
in reverse order.
9. Using a flat spanner, tighten the outer lock-
nut (O) against the inner locknut (N).
NOTE: Do not over-tighten and do not restrict the move-
ment of the spindle!
Service information
Please note that the following parts of this product are sub-
ject to normal or natural wear and that the following parts are
therefore also required for use as consumables.
Wear parts*: Kohlebürsten; Keilriemen, Batterien, Bohrer
* Not necessarily included in the scope of delivery!
13. Storage
Store the device and its accessories in a dark, dry and frost-
proof place that is inaccessible to children. The optimum stor-
age temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust and moisture.
Store the operating manual with the electrical tool.
To Next Page
Loading...
