What to do if the Scheppach Drill bit binds in the workpiece?
If the Scheppach Drill bit binds in the workpiece, it might be due to the workpiece pinching or excessive feed pressure. Support or clamp the workpiece. Also, adjust the belt tension.
What to do if the Scheppach DP16VLS Drill workpiece is torn loose from hand?
If the Scheppach Drill workpiece is torn loose from your hand, you should support or clamp the workpiece.
Why does the quill on my Scheppach Drill return too slowly or quickly?
The quill on your Scheppach Drill returns too slowly or quickly because the spring has improper tension. Adjust the spring tension.
Why won't the chuck stay attached to the spindle of my Scheppach DP16VLS?
If the chuck won't stay attached to the spindle on your Scheppach Drill, it is because there is dirt, grease, or oil on the taper of the chuck or on the spindle's tapered inside surface. Clean the tapered surfaces of the chuck and spindle using household detergent to remove all dirt, grease, and oil.
Why does my Scheppach Power Tool drill bit burn?
Drill bit burning in your Scheppach Power Tool can occur due to several reasons: * The speed may be incorrect, so you should change the speed. * Chips might not be coming out of the hole. Retract the drill bit frequently to remove chips. * The drill bit may be dull, so resharpen the drill bit. * The feed may be too slow, so increase the feed rate.
What to do if the workpiece is torn loose from my hand using Scheppach Drill?
If the workpiece is torn loose from your hand while using the Scheppach Drill, it indicates that it is not supported or clamped properly. Support the workpiece or clamp it.
How to fix a Scheppach Drill that leads off, resulting in a non-round hole?
If your Scheppach Drill leads off and the hole isn't round, it could be due to: 1. Hard grain in the wood or the angle and/or length of cutting lips are not equal, so resharpen the drill bit correctly. 2. A bent drill bit, so replace the drill bit.
Why does my Scheppach DP16VLS Drill bit bind in the workpiece?
A drill bit binding in the workpiece with your Scheppach Drill can occur because: 1. The workpiece is pinching due to feed pressure, so support the workpiece or clamp it. 2. The belt tension is improper, so adjust the belt tension.
What to do if my Scheppach DP16VLS Drill bit has excessive run-out or wobble?
Excessive drill bit run-out or wobble in your Scheppach Drill can stem from: 1. A bent drill bit, so use a straight drill bit. 2. Worn spindle bearings, which require replacement. 3. The drill bit not being properly installed in the chuck, so install the drill properly. 4. The chuck not being properly installed, so properly install the chuck.
How to fix a noisy Scheppach Drill?
A noisy Scheppach Drill can be caused by several factors: 1. Incorrect belt tension, which requires adjustment. 2. A dry spindle, which needs lubrication. 3. A loose spindle pulley, so check the retaining nut and tighten if necessary. 4. A loose motor pulley, which requires tightening the set screw.
General safety guidelines for using electric tools.
Proper techniques for operating the electric tool safely.
Warning about laser radiation and precautions.
Guidelines for maintaining a safe working environment.
Essential safety measures when using the laser.
Precautions related to electrical hazards and connections.
Specific safety precautions for drill operation.
Warning about electromagnetic fields and medical implants.
Personal safety measures and attentiveness during operation.
Steps for assembling the column and base.
Instructions for mounting the drilling table onto the pillar.
Guide to selecting spindle speeds and adjusting belts.
Risks and checks for damaged power cables.
General| Drilling | Yes |
|---|---|
| Screwdriving | - |
| Product color | Blue, Grey |
| Input power | 500 W |
| Power source | AC |
| AC input voltage | 230 - 240 V |
| AC input frequency | 50 Hz |
| Idle speed (max) | - RPM |
| Chuck capacity (max) | 16 mm |
| Drilling diameter in steel (max) | - mm |
| Product type | Bench drill press |
| Housing material | Steel |
| Drill table size (WxD) | 160 x 160 mm |
Weight and Dimensions| Depth | 460 mm |
|---|---|
| Width | 380 mm |
| Height | 250 mm |
| Weight | 15420 g |
To Next Page
