www.scheppach.com
GB
|
23
16 Important!
- For your own safety you must only use the acces-
sories and additional units listed in the operating
instructions or recommended or specied by the
manufacturer. The use of mounted tools or acces-
sories other than those recommended in the op-
erating instructions or catalogue may place your
personal safety at risk.
17 Noise
- Wear ear muffs when you use the compressor.
18 Replacing the power cable
- To prevent hazards, leave the replacement of
damaged power cables strictly to the manufac-
turer or a qualied electrician. There is a risk of
electric shock!
19 Inating tires
- Directly after inating tires, check the pressure
with a suitable pressure gauge, for example at
your lling station.
20 Roadworthy compressors for building site oper-
ations
- Make sure that all lines and ttings are suitable
for the maximum permissible operating pressure
of the compressor.
21 Place of installation
- Set up the compressor on an even surface.
22 Supply hoses at pressures above 7 bar should be
equipped with a safety cable (e.g. a wire rope).
23 Avoid over-stressing the piping system by using
exible hose connections to prevent kinking.
24 Use a residual current circuit breaker with a trigger
current of 30 mA or less. Using a residual current
circuit breaker reduces the risk of an electric shock.
25. Ensure that oil cooling devices are kept clean and
protective devices remain in operational condition.
26. Risk of burns from hot oil
- Wear suitable protective gloves.
- Never work with the compressor near naked
ames.
- Be careful not to spill oil.
27. Motor start-up is prohibited at low temperatures be-
low 0 °C.
m WARNING! This electric tool generates an elec-
tromagnetic eld during operation. This eld can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operating
the electric tool.
9 Take care of your tools
- Keep your compressor clean in order to work well
and safely.
- Follow the maintenance instructions.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check extension cables regularly and replace
them when damaged.
10 Pull the plug out of the outlet
- During non-use of the electric tool or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
11 Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
12 Use extension cables for outdoors
- Only use approved and appropriately identied
extension cables for use outdoors.
- Only use cable reels in the unrolled state.
13 Remain attentive
- Pay attention to what you are doing. Remain sen-
sible when working. Do not use the electric tool
when you are distracted.
14 Check the electric tool for potential damage
- Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use of
the electric tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and all
conditions must be fullled to ensure fault-free
operation of the electric tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is specied
in the operating manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use any faulty or damaged connection
cables.
- Do not use any electric tool on which the switch
cannot be switched on and off.
15 Have your electric tool repaired by a qualied
electrician
- This electric tool conforms to the applicable safe-
ty regulations. Repairs may only be performed by
an electrician using original spare parts. Other-
wise accidents can occur.
To Next Page
Loading...
Need help?
General
