Scheppach HM254 User Manual

www.scheppach.com
GB
|
29
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes.
Even when the equipment is used as prescribed it is
still impossible to eliminate certain residual risk factors.
The following hazards may arise in connection with the
machine’s construction and design:
• Contact with the saw blade in the uncovered saw
zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces.
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw blade.
• Damage to hearing if ear-mu󰀨s are not used as ne-
cessary.
• Harmful emissions of wood dust when used in clo-
sed rooms.
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications.
Our warranty will be voided if the equipment is used in
commercial, trade or industrial businesses or for equi-
valent purposes.
5. Safety information
General power tool safety warnings
m WARNING: Read all safety warnings, instructi-
ons, illustrations and specications provided with
this power tool. Failure to follow all instructions listed
below may result in electric shock, re and/or serious
injury.
Save all warnings and instructions for future refe-
rence.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-opera-
ted (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
33. ON/OFF switch laser
34. Guide bracket
35. Latched position lever
36. Tilt protection
A.) 90° stop angle (not supplied)
B.) 45° stop angle (not supplied)
C.) Allen key, 6 mm
D.) Allen key, 3 mm
E.) Philips head screw (Laser)
3. Scope of delivery
• Crosscut, drag and mitre saw
• 1 x Clamping device (7) (preassembled)
• 2 x Workpiece support (8) (preassembled)
• Sawdust bag (17)
• Allen key 6 mm (C)
• Allen key 3 mm (D)
• Operating manual
4. Intended use
The crosscut, drag and mitre saw is designed to cros-
scut wood and plastic respective of the machine’s size.
The saw is not designed for cutting rewood.
Warning! Do not use the saw to cut materials other
than those specied described in manual.
Warning! The supplied saw blade is only intended for
the sawing of wood! Do not use this blade for the sa-
wing of rewood!
The equipment is to be used only for its prescribed pur-
pose. Any other use is deemed to be a case of misuse.
The user / operator and not the manufacturer will be
liable for any damage or injuries of any kind caused as
a result of this.
The equipment is to be operated only with suitable saw
blades. It is prohibited to use any type of cutting-o󰀨
wheel.
To use the equipment properly you must also observe
the safety information, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the equipment have to
be acquainted with this manual and must be informed
about the equipment’s potential hazards. It is also im-
perative to observe the accident prevention regulations
in force in your area. The same applies for the general
rules of health and safety at work.

Scheppach HM254 Specifications

General

Laser guide	Yes
Product color	Blue, Grey
Sliding rails	-
Number of blade teeth	60
Input power	2000 W
Power source	AC
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Idle speed (max)	- RPM
Cutting width (90°)	340 mm

Weight and Dimensions

Depth	820 mm
Width	480 mm
Height	410 mm
Weight	17560 g