Scheppach HS410 User Manual

www.scheppach.com
GB
|
25
• The safety, work and maintenance instructions of
the manufacturer as well as the dimensions indicat-
ed in the Technical Data section must be adhered to.
• Relevant accident prevention regulations and other,
generally recognized safety-technical rules must
also be adhered to.
• The machine may only be used, maintained, and
operated by persons familiar with it and instructed
in its operation and procedures. Arbitrary alterations
to the machine release the manufacturer from all re-
sponsibility for any resulting damages.
The machine may be operated only with original parts
and original accessories of the manufacturer.
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications.
Our warranty will be voided if the equipment is used
in commercial, trade or industrial businesses or for
equivalent purposes.
5. Safety notes
• Warning: When using electric tools it is imperative to
take the following basic safety precautions in order
to reduce the risk of electric shock, injury and re.
• Take due note of all this information before and while
working with the saw.
• Do not lose these safety regulations.
• Guard against electric shock
• Avoid body contact with earthed parts.
• When equipment is not being used it should be kept
in a dry, closed place out of childrens reach.
• Keep mounted attachments sharp and clean to ena-
ble you to work well and safely.
• Check the power cable regularly and have it re-
placed by an authorized specialist at the rst sign
of any damage.
• Check your extension cables regularly and replace
them if damaged.
• When working outdoors, use only extension cables
that are approved for outdoor use and which are
marked accordingly.
• Concentrate on what you are doing. Use common
sense when working. Do not operate the tool if your
mind is not on your work.
• Never use an electric tool with a switch that cannot
be turned on and o󰀨.
• Warning! The use of other tools and accessories
may put you at risk of injury.
• Always pull the plug out of the power socket before
adjusting or servicing the machine.
4. Intended use
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufactur-
er will be liable for any damage or injuries of any kind
caused as a result of this.
The equipment is to be operated only with suitable
saw blades. It is prohibited to use any type of cut-
ting-o󰀨 wheel.
To use the equipment properly you must also observe
the safety information, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the equipment have
to be acquainted with this manual and must be in-
formed about the equipment’s potential hazards.
It is also imperative to observe the accident prevention
regulations in force in your area. The same applies for
the general rules of health and safety at work.
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes.
The machine corresponds to the valid EC guide-
line.
• The log saw is constructed as 1-man-operating
stand and is only to be used in outdoor locations.
• The log saw is a portable circular saw. It is only ap-
plicable to cross cut rewood with a feeding rocker
according to the technical specications.
• The saw is constructed solely for cross cutting of
rewood.
• Regardless of the diameter of the wood only 1 work
piece is to be put on the rocker.
• Observe all safety and hazard notes on the machine
and ensure they are kept complete and in a legible
condition.
• The machining range and surrounding areas of the
machine must be clear of interfering foreign matter
to prevent accidents occurring.
• Workpieces must be completely free of foreign ob-
jects, i.e. nails or screws.
• The machine must only be used in technically per-
fect condition in accordance with its designated use
and the instructions set out in the operating manual,
and only by safety-conscious persons who are fully
aware of the risks involved in operating the machine.
Any functional disorders, especially those a󰀨ecting
the safety of the machine, should therefore be recti-
ed immediately.

Scheppach HS410 Specifications

General

Idle speed	- RPM
Product color	Black, Blue, Grey
Placement supported	Freestanding
Input power	2200 W
AC input voltage	230 V
Saw blade included	Yes

Weight and Dimensions

Depth	1080 mm
Width	780 mm
Height	250 mm
Weight	43600 g
Blade diameter	405 mm