29IE/NI
1. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-
cians,
• Installation and replacement of non-original spare parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due to the
non-compliance of the electric regulations and VDE regula-
tions 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instructions
before installing and commissioning the device.
The operating instructions are intended to help the user to
become familiar with the machine and take advantage of its
application possibilities in accordance with the recommenda-
tions.
The operating instructions contain important information
on how to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, reduce
downtimes and how to increase reliability and service life of
the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt
and moisture. Read the instruction manual each time before
operating the machine and carefully follow its information.
The machine can only be operated by persons who were
instructed concerning the operation of the machine and who
are informed about the associated dangers. The minimum age
requirement must be complied with.
In addition to the safety instructions contained in this operat-
ing manual and the specific regulations of your country,
the technical rules generally accepted for the operation of
machines of the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety
information.
2. Device description (Abb. A-M)
1. Extractor connector
2. Scale for depth of cut
3. Plunge-cut trigger
4. Handle/hand grip
5. Front handle
6. Scale for mitre square
7. Adjustment screw for depth of cut
8. ON/OFF switch
9. Adjustment screw for guide rail
10. Tilt Protection
11. Motor
12. Base plate
13. 90-degree adjustment screw
14. Mitre adjustment screw
15. Saw blade
16. Riving knife
17. Adjustment screw for riving knife
18. Shaft locking mechanism
19. Saw blade locking screw
20. Outer flange
21. Guide rails a´ 700 mm (2 Items)
22. Rail Joiner
3. Scope of delivery
• 1 Piece Plunge Cut Saw
• 2 Pieces Screw Clamps á 700mm
• 1 Piece Rail Joiner
• 1 Piece Tilt Protection
• 1 Piece allen key 5 mm
• Translation from the original instruction manual
4. Intended use
Plunge-cut saws are intended to be used for sawing wood, ma-
terials similar to wood and plastics.
The machine is designed and approved for use by trained per-
sons or specialists only.
Only saw blades suitable for the machine (HM or CV saw
blades) may be used. HSS saw blades or cutting discs of any
kind may not be used.
Any other applications are expressly prohibited and are
deemed improper use.
Neither the manufacturer nor the retailer can accept any re-
sponsibility for injury, loss or damage caused by misuse of this
product of any kind.
Examples of misuse are given in the following non-exhaustive
list:
• Using the plunge saw for other purposes than those which
are intended;
• Failure to observe the safety instructions and warnings as
well as the assembly, operating, maintenance and cleaning
instructions contained in this user manual;
• Failure to comply with any regulations relating to accident
prevention, occupational medicine or safety which specifi-
cally and/or generally apply to the use of this plunge saw;
• Use of accessories or spare parts that are not intended for
this plunge saw;
• Modifications to the plunge saw;
To Next Page
Loading...
Need help?
General
