Scheppach RoboCut L500 User Manual

GB
|
31
9.2.1 Changing the PIN code (Fig. 21)
• Press and hold the “START” and “HOME” buttons
simultaneously for at least 3 seconds.
• The symbol and “PIN” ash.
• Now enter the old PIN code as follows (factory set-
ting “0000”).
• The rst digit illuminates (“0---”).
• Use the “START” and “HOME” buttons to select the
desired digit.
• Conrm the digit with the “OK” button.
• The next digit illuminates (e.g. “10--).
• Proceed as described in paragraph 2-4 above.
• After you have entered the “old” PIN code and con-
rmed the fourth digit with the “OK” button, “PIn2”
appears, now you can enter the new PIN code.
• The rst digit ashes (“0---”).
• Use the “START” and “HOME” buttons to select the
desired digit.
• Conrm the digit with the “OK” button.
• The next digit ashes (e.g. “10--).
• Proceed as described in paragraph 2-4 above.
• After conrming the fourth digit with the “OK” but-
ton, the new PIN code is stored. The word “IdLE”
appears on the display.
9.2.2 Setting/changing the date/time (Fig. 22)
m NOTE
Date and time are necessary settings so that the ro-
botic lawnmower (1) can mow in accordance with the
set mowing schedule.
• The date/time setting is done in the order year -
date - time.
• Press and hold the “START” button for at least 5
seconds.
• The - symbol and a number (e.g. 2020) ashes
on the display.
• Use the “START”, “HOME” and “OK” buttons to set
the year, similarly to the PIN setting.
• Then the next number illuminates (month.day e.g.
08.25 for 25 August).
• Use the “START”, “HOME” and “OK” buttons to set
the correct month and day.
• The time is displayed last (e.g. 13:25).
• Set the current time as described above.
• After conrming the fourth digit with the “OK” but-
ton, the date and time are stored. The word “IdLE”
appears on the display.
9.2.3 Changing the start time (Fig. 23)
The factory-set start time of 09:00 can be changed
at any time.
• Press and hold the “START” and “OK” buttons si-
multaneously for at least 3 seconds.
• The display shows the set start time, e.g. 13:25,
with the rst digit ashing.
Switching the robotic lawnmower on:
• The robotic lawnmower can then be restarted as
described below.
•
m NOTE
Before the robotic lawnmower (1) starts mowing, an
acoustic signal (four beeps) is heard, then the blade
disc (6) starts rotating.
• Press the (“POWER ON/ OFF” button) until the
robotic lawnmower (1) switches on.
• For the rst use, enter the default PIN code “0000”
by pressing “OK” four times when the number “0”
ashes. (The PIN code can be changed as de-
scribed in point 9.2.1).
• After conrming the fourth digit with the “OK but-
ton”, the robotic lawnmower is ready for use. The
word “IdLE” appears on the display.
m NOTE
The robotic lawnmower (1) switches o󰀨 automatically
after 30 seconds if no input is made.
m ATTENTION
If the PIN code is entered incorrectly 10 - times,
“LOCK” appears on the display. The device is now
locked for 10 minutes before you can enter the PIN
code again.
• Press the “START” button and then the “OK” button
to start mowing.
• If you press the “HOME” button and then the “OK”
button, the robotic lawnmower (1) returns to the
charging station (10) with the mowing function
switched o󰀨.
The robotic lawnmower (1) operates continuously un-
til the battery charge is too low. The robotic lawnmow-
er automatically returns to the charging station (10).
The cutter disc is deactivated in this state.
m NOTE
After the rechargeable battery is fully charged, the
robotic lawnmower starts again. Alternatively, the ro-
botic lawnmower remains in the charging station (10)
in accordance with the set mowing schedule.
(By default, the robot mows from Monday to Friday
from 09:00 - 15:00 hrs)
9.2. Settings
m NOTE
To make adjustments to the product, the robotic lawn-
mower (1) must be switched on. Switch on the robotic
lawnmower (1) by pressing the button and hold the
key (“POWER ON-/OFF” key) until “PIN” appears on
the display.

Scheppach RoboCut L500 Specifications

General

Brand	Scheppach
Model	RoboCut L500
Category	Lawn Mower
Language	English