To Next PageTo Next PageWhat does 'bAD / bAt / F01' mean on my Schumacher Electric SC1309?
If your Schumacher Electric Battery Charger display shows “bAD / bAt / F01”, it indicates that the battery voltage is still below 10V (for a 12V battery) or 5V (for a 6V battery) after 2 hours of charging. The battery may be defective. Make sure there are no loads on the battery. If there are, remove them. If there are none, have the battery checked or replaced.
What does 'bAD / bAt / F05' mean on my Schumacher Electric SC1309 Battery Charger?
If your Schumacher Electric Battery Charger displays “bAD / bAt / F05”, it means a lack of progress was detected after 12 hours in Maintain mode. This may be caused by a drain on the battery, or the battery could be bad. Ensure there are no loads on the battery. If there are, remove them. If there are none, have the battery checked or replaced.
What to do if Schumacher Electric SC1309 will not turn on?
If your Schumacher Electric Battery Charger doesn't turn on when properly connected, check the AC outlet for an open fuse or circuit breaker. Also, inspect the power cord and any extension cords for loose connections. If these steps don't resolve the issue, have the battery checked by a professional.
What to do if Schumacher Electric SC1309 shows bAd bAT F02?
If your Schumacher Electric Battery Charger displays “bAd bAT F02”, it means the battery could not be desulfated. Have it checked or replaced.
What does bAd bAT F05 mean on my Schumacher Electric SC1309 Battery Charger?
If your Schumacher Electric Battery Charger shows “bAd bAT F05”, it may be caused by a drain on the battery, or the battery could be bad. Make sure there are no loads on the battery. If there are, remove them. If there are none, have the battery checked or replaced.
What does error code F03 mean on my Schumacher Electric Battery Charger?
If your Schumacher Electric Battery Charger displays “F03”, it may be caused by trying to charge a large battery or bank of batteries on too low of a current setting. Try again with a higher current setting, or have the battery checked or replaced.
Why does my Schumacher Electric SC1309 Battery Charger show bAd bAT F01?
If your Schumacher Electric Battery Charger shows “bAd bAT F01”, the battery could be bad. Have it checked or replaced.
What to do if my Schumacher Electric SC1309 Battery Charger displays F04?
If your Schumacher Electric Battery Charger displays “F04”, it means the battery is connected backward. Unplug the charger and reverse the connections to the battery.
What does bAd bAT F02 mean on Schumacher Electric Battery Charger?
If your Schumacher Electric Battery Charger displays “bAD / bAt / F02”, it means that desulfation was unsuccessful after 10 hours. The battery may be defective, so have it checked or replaced.
What to do if Schumacher Electric SC1309 engine start does not work?
If the engine start function on your Schumacher Electric Battery Charger isn't working, it could be due to several reasons: you might be drawing more current than the engine start rate allows, you might not be waiting the required 3 minutes (180 seconds) between cranking attempts, the charger may be overheating, or the battery may be severely discharged. * Crank time varies with the amount of current drawn. If cranking draws more than the Engine Start rate, crank time may be less than 5 seconds. * When the Engine Start LED blinks, wait 3 minutes of rest time before the next crank. * Ensure the charger vents are not blocked. Wait and try again. * For a severely discharged battery, use the boost rate for 10 to 15 minutes to assist with cranking.
General| Product Type | Battery Charger |
|---|---|
| Voltage | 12V |
| Charging Modes | Automatic, Manual |
| Input Voltage | 120V AC |
| Output Voltage | 12V DC |
| Battery Type | AGM, Gel |
| Features | Reverse hook-up protection |
| Compatibility | Automotive, Marine, Power Sport Batteries |
| Safety Features | Overcharge Protection |
Guidelines to protect yourself from hazards when working with batteries and chargers.
Warning about explosive gases generated by batteries and how to mitigate risks.
Safety measures for connecting and disconnecting DC clips to prevent sparks.
Explanation of the ON/OFF switch positions for charging, maintaining, and engine start.
Step-by-step guide to charging a battery while it remains in the vehicle.
Step-by-step guide to charging a battery that has been removed from the vehicle.
How to use the Boost mode to quickly add energy to a discharged battery.
How to use the Engine Start feature to jump-start a vehicle.
Table listing error codes, their descriptions, and reasons/solutions.
Troubleshooting steps for a charger that will not turn on when properly connected.
Explanations and solutions for specific error codes displayed by the charger.
