SEA ‘SWING 2’ Control Panel Programming Guide
This guide is intended to be used in conjunction with the booklet supplied with the unit.
Before starting programming check all the ‘Normally Closed Inputs either have a device fitted for example;
A Stop Button, set of Photocells or are wire-linked out and the following 3 led are lit:-
Stop input: – led 1
Photocell 2 input: – led 4
Photocell 1 input: – led 5
The motor run times can be programmed in two ways:-
1) By programming run times and leaf delays using the ‘Self-learn’ button – P 1
Or
2) By adjusting the motor run times and closing leaf delay by adjusting the Trimmers
Option 1 – Self-learn
Starting with the ‘Swing 2’ de-powered. Manually move the gates to 45° and re-connect releases.
Set all the dip switches to the OFF position and rotate Trimmer RV3 fully clockwise. Switch-on the power.
The following programming sequence will require a total of 9 presses of Button P1 - The first is a long press (approx. 10
seconds.) to enter the programming phase the subsequent 8 presses are all short approx. 1 second duration.
Both motors must first run towards closed when starting the programming phase – Invert the black & brown motor wires of
motors that initially run towards the open direction.
Leaf Delay cannot be excluded from this programme. For minimum ‘Leaf Delay’, Button P1 should be immediately re-
pressed as soon as the motor starts running on ‘Press number 4 and 7. This will keep the delay down to a minimum.
1. Press P1 for approximately 10 seconds – until led P lights and Motor 2 starts running towards closed.
2. Press P1 again when Motor 2 strikes the closed stop – Motor 2 will stop and Motor 1 starts to close.
3. Press P1 again when Motor 1 strikes the closed stop – Motor 1 will stop, then automatically start to run towards open.
4. Press P1 again to set the amount of leaf delay in opening – Motor 1 will pause for a second then continue opening.
5. Press P1 again when Motor 1 strikes the open stop – Motor 1 will stop and Motor 2 will start to open.
6. Press P1 again when Motor 2 strikes the open stop – Motor 2 will stop and then automatically start to close.
7. Press P1 again to set the amount of leaf delay in closing – Motor 2 will pause for a second then continue closing.
8. Press P1 again when Motor 2 strikes the closed stop – Motor 2 will stop and Motor 1 will start to close.
9. Press P1 again when Motor 1 strikes the closed stop – The Programming mode finishes and led P goes out
Test the timings are correct. If so, additional logic selections can now be made i.e. Slowdown or Reversing Stroke etc.
To select Operating Logic put dip switch 1 into the required position.
Trimmer RV2 adjusts the amount of ‘Slow-down’ when working in this programming mode.
Trimmer RV3 adjusts the ‘Automatic Closing Times, turn anti-clockwise to select the required time.
Option 2 – Trimmer Adjustment
Put logic ‘dip switch’ 8 into the ON position and turn ‘Trimmer RV3 to the fully clockwise position.
N.B. Because not all Trimmer alterations are registered until the cycle has completed, make any necessary ‘Trimmer’
adjustments when the gates have fully completed a cycle and are at rest in the closed position.
Trimmer RV1 – Adjusts the ‘Motor Torque’ (power) on electro-mechanical operators - Set at maximum for hydraulic
Operators and adjust the operators power by working on the pressure adjusting valves.
Trimmer RV2 – Adjusts the amount of ‘Leaf Delay’ in closing when programming in this mode. Leaf Delay in opening is
preset and non-adjustable.
Trimmer RV3 – Adjusts the ‘Leaf Delay’ in Closing’.
Trimmer RV4 – Adjusts the ‘Motor Run Times’.
To Next Page
Need help?
General
