To Next PageTo Next PageHow to fix Seaflo Water Pump that will not prime?
If your Seaflo Water Pump won't prime, it could be due to: * **Inlet air leak:** Tighten the fittings or replace any cracked fittings. * **Inlet/Outlet tube restriction:** Remove any obstructions in the inlet or outlet tubes. * **Incorrect voltage:** Ensure the voltage is within the correct range (±10%).
Why my Seaflo SFDP1-055-060-51 Water Pump will not turn on?
If your Seaflo Water Pump won't turn on, here's what to check: * **Bad electrical connection:** Inspect and correct battery connections. * **Short in wires:** Examine the wires for any damage or shorts. * **Faulty pressure switch:** Consider replacing the pressure switch assembly. * **Incorrect voltage:** Verify the voltage is within the specified range (±10%).
Why is the pressure low on my Seaflo SFDP1-055-060-51?
If you're experiencing low pressure or flow with your Seaflo Water Pump, the following could be the cause: * **Worn wobble plate or diaphragm:** Replace the diaphragm assembly. * **Worn pressure switch:** Replace the pressure switch assembly. * **Inlet/Outlet tube restriction:** Remove any restrictions in the inlet or outlet tubes.
Why is my Seaflo Water Pump operating roughly?
If your Seaflo Water Pump is running roughly, consider these factors: * **Flexible mounting surface:** Mount the pump on a rigid surface. * **Loose pump head:** Tighten the fasteners. * **Compressed base feet:** Decompress the base feet. * **Rigid plumbing:** Plumb the pump with flexible plumbing.
What to do if my Seaflo SFDP1-055-060-51 leaks?
If your Seaflo Water Pump is leaking, the issue might be: * **Leak in diaphragm:** Replace the diaphragm assembly. * **Leak in the system:** Tighten any loose fittings or replace cracked fittings. * **Faulty pressure switch:** Consider replacing the pressure switch assembly.
What to do if Seaflo SFDP1-055-060-51 Water Pump cycles while not spraying?
If your Seaflo Water Pump cycles even when it's not spraying, check these: * **Incorrect voltage:** Make sure the voltage is within the specified range (±10%). * **Air trapped in system:** Purge any trapped air from the system.
General| Model | SFDP1-055-060-51 |
|---|---|
| Voltage | 12V DC |
| Flow Rate | 5.5 GPM (20.8 LPM) |
| Ports | 1/2" NPT |
| Type | Diaphragm Pump |
| Pressure | 60 PSI (4.1 Bar) |
Guidelines for using the pump with pesticides, including limitations and safety precautions.
Approved uses for non-flammable liquids like water, dust control, and sealants.
Safety precautions and checks required during the pump assembly process.
Essential safety information to follow while operating the pump with chemicals.
Pre-application checks and safety measures before starting the spraying process.
Safety rules and procedures to follow while the pump is actively spraying.
Post-spraying procedures for cleaning, decontamination, and disposal.
Guidelines for immediate response to chemical spills, leaks, or personal exposure.
Instructions on how and where to properly mount the SEAFLO pump.
Guidance on connecting hoses and fittings to the pump ports.
Detailed steps for safely connecting the pump to a power source.
Specific safety measures for applying chemicals to avoid exposure and environmental harm.
Procedures for inspecting and preparing the pump before each operation.
Step-by-step guide on how to operate the pump safely and effectively.
Instructions for preparing the pump for end-of-season storage to prevent damage.
Steps to take when taking the pump out of storage for use.
Safety precautions and preparatory steps before troubleshooting or servicing the pump.
A guide to diagnose and resolve common pump problems and their solutions.
Technical details, flow rates, voltage, and pressure for different pump models.
Information on materials used in pump components and chemical compatibility.
Details of the limited warranty period, coverage, and exclusions.
