EasyManua.ls Logo

Sears Craftsman 247.881731 - User Manual

Sears Craftsman 247.881731
76 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Sears Brands Management Corporation, Hoffman Estates, IL 60179, U.S.A.
Visit our website: www.craftsman.com
CAUTION: Before using this
product, read this manual and
follow all safety rules and operating
instructions.
Operator’s Manual
• SAFETY
• ASSEMB LY
• OPERATION
• MAINTENANCE
• PARTSLIST
• ESPAÑOL
®
24” SNOW THROWER
Model No. 247.881731
Form No. 769-08174C
(June 21, 2013)

Table of Contents

Questions and Answers

  • C
    Christina AlexanderJul 28, 2025
    Why Sears Snow Blower engine fails to start?
    • K
      Kenneth McguireJul 28, 2025
      The Sears Snow Blower engine might fail to start due to several reasons: the choke control may not be in the CHOKE position (move it to the CHOKE position); the spark plug wire might be disconnected (connect it); the spark plug could be faulty (clean, adjust the gap, or replace it); the fuel tank may be empty or contain stale fuel (fill it with clean, fresh gasoline); the engine might not be primed (prime it as instructed); the key may not be inserted (insert it fully); or the extension cord might not be connected when using the electric start (connect it to a grounded outlet).
  • D
    dominique03Aug 1, 2025
    What to do if Sears Craftsman 247.881731 unit fails to discharge snow?
    • J
      Joseph FergusonAug 1, 2025
      If your Sears Snow Blower fails to discharge snow, it could be due to a clogged chute assembly (stop the engine, disconnect the spark plug wire, and clean the chute assembly with a clean-out tool or stick); a foreign object lodged in the auger (stop the engine, disconnect the spark plug wire, and remove the object with a clean-out tool or stick); the auger cable needing adjustment (adjust the auger control cable); a loose or damaged auger belt (replace the auger belt); or sheared shear pins (replace them with new ones).
  • A
    Ashley MarshallAug 6, 2025
    Why Sears Craftsman 247.881731 Snow Blower engine running erratically?
    • J
      Joseph ArcherAug 6, 2025
      An erratic running Sears Snow Blower engine may be caused by several factors: the engine running on CHOKE (move the choke control to the RUN position); stale fuel (fill the tank with clean, fresh gasoline); or water or dirt in the fuel system (drain the fuel tank and refill with fresh fuel). For carburetor or over-governed engine issues, it is advised to contact your Sears Parts & Repair Center.
  • W
    William MooreAug 10, 2025
    What causes loss of power in Sears Craftsman 247.881731?
    • M
      Michael FloresAug 10, 2025
      A loss of power in your Sears Snow Blower could stem from a loose spark plug wire (connect and tighten it) or a plugged gas cap vent hole (remove any ice and snow from the gas cap, ensuring the vent hole is clear).
  • N
    Natasha GilbertAug 14, 2025
    What to do if Sears Craftsman 247.881731 Snow Blower has excessive vibration?
    • W
      williamdawsonAug 14, 2025
      If your Sears Snow Blower experiences excessive vibration, immediately stop the engine and disconnect the spark plug wire. Tighten all bolts and nuts. If the vibration persists, it is recommended to have the unit serviced by a Sears Parts & Repair Center.
  • J
    Jessica OliverAug 19, 2025
    Why Sears Craftsman 247.881731 Snow Blower unit fails to propel itself?
    • A
      Ashley HamiltonAug 19, 2025
      If your Sears Snow Blower fails to propel itself, the drive cable may need adjustment or the drive belt may be loose or damaged. It is also possible that the friction wheel is worn. For these issues, it is advised to contact your Sears Parts & Repair Center.
  • R
    Richard ThompsonAug 23, 2025
    How to fix Sears Snow Blower chute that fails to easily rotate?
    • C
      Christian RobinsonAug 23, 2025
      If the chute on your Sears Snow Blower fails to easily rotate, it might be assembled incorrectly. Disassemble the chute control and reassemble it as directed in the Assembly section.

Summary

Warranty Statement

Warranty Coverage and Exclusions

Safety Instructions

General Safety, Training, and Preparation

Covers warnings, dangers, training, preparation, and gasoline safety.

Safe Operation and Maintenance Basics

Guidelines for safe operation, chute clearing, and basic maintenance.

Engine, Emissions, and Spark Arrestor Safety

Warnings on engine modification, emissions, and spark arrestors.

Understanding Safety Symbols

Explains various safety symbols and their meanings.

Assembly

Carton Removal and Initial Assembly

Chute and Control Assembly

Continues assembly instructions for chute and controls.

Setup and Skid Shoe Adjustment

Includes setup for chute tool, tire pressure, and skid shoe adjustments.

Operation

Chute and Auger Control Adjustment

How to adjust chute angle and auger control.

Key Controls Overview

Engine, Drive, and Chute Controls

Details throttle, primer, drive/auger controls, chute, and skid shoes.

Pre-Start Procedures and Starting Engine

Covers clean-out tool, oil, gasoline, starting the engine, and electric starter.

Starting, Stopping, and Engaging Controls

Details starting methods, stopping, engaging drive/auger, and shear pins.

Service and Maintenance

Maintenance Schedule and Oil Checks

Schedule for maintenance and how to check engine oil.

Engine Oil Change and Spark Plug Maintenance

Steps for changing engine oil and maintaining the spark plug.

Lubrication and Component Wear

Adjustments and Cable Tuning

How to adjust cables and chute pre-load.

Auger Belt Replacement

Steps for removing and replacing the auger belt.

Belt Replacement and Friction Wheel Removal

Continues auger belt replacement and friction wheel removal.

Friction Wheel Assembly

Continues friction wheel assembly removal and reassembly.

Off-Season Storage

Engine and Machine Storage Preparation

Steps for preparing the engine and machine for long-term storage.

Troubleshooting

Engine and Propulsion Issues

Troubleshooting for engine start, erratic operation, vibration, and propulsion.

Snow Discharge and Chute Problems

Troubleshooting for improper snow discharge and chute rotation.

Warranty Statement (Spanish)

Warranty Coverage Details (Spanish)

Safety Instructions (Spanish)

General Safety, Training, and Preparation (Spanish)

Covers warnings, dangers, training, preparation, and gasoline safety.

Safe Gasoline Handling and Operation (Spanish)

Maintenance, Storage, and Engine Safety (Spanish)

Safety Symbols Explained (Spanish)

Assembly (Spanish)

Carton Removal and Initial Assembly (Spanish)

Chute and Control Assembly (Spanish)

Setup and Skid Shoe Adjustment (Spanish)

Operation (Spanish)

Chute and Auger Control Adjustment (Spanish)

Key Controls Overview (Spanish)

Engine, Drive, and Chute Controls (Spanish)

Pre-Start Procedures and Starting Engine (Spanish)

Covers clean-out tool, oil, gasoline, starting the engine, and electric starter.

Starting, Stopping, and Engaging Controls (Spanish)

Service and Maintenance (Spanish)

Maintenance Schedule and Oil Checks (Spanish)

Engine Oil Change and Spark Plug Maintenance (Spanish)

Spark Plug Check and Lubrication (Spanish)

Adjustments and Cable Tuning (Spanish)

Auger Belt Replacement (Spanish)

Belt Replacement and Drive Belt (Spanish)

Friction Wheel Removal (Spanish)

Friction Wheel and Auger Pin Maintenance (Spanish)

Off-Season Storage (Spanish)

Engine and Machine Storage Preparation (Spanish)

Troubleshooting (Spanish)

Engine and Propulsion Issues (Spanish)

Power, Snow Discharge, and Chute Problems (Spanish)

Sears Craftsman 247.881731 Specifications

General IconGeneral
Product TypeGas Snow Blower
Engine Type4-Cycle
Engine Displacement208cc
EngineBriggs & Stratton
Clearing Width24 inches
Intake Height21 inches
Drive SystemSelf-propelled
Weight200 lbs
Number of Forward Speeds6
Number of Reverse Speeds2
Start TypeElectric Start
Auger MaterialSteel
Chute ControlRemote
Tire Size13 x 4 inches
Stages2-stage

Related product manuals