How to fix a noisy Seeley Breezair EXT Accessories cooler?
If your Seeley Accessories cooler is making excessive noise, start by cleaning the fan, as dirt or debris can cause imbalance. If the noise persists, it may be due to too much back pressure in the system. In this case, re-evaluate the design, improve the duct layout, or change the grille sizes to reduce back pressure.
What to do if the Seeley Breezair EXT Accessories cooler pump fails to operate?
If the pump in your Seeley Accessories cooler fails to operate, first check the circuit breaker. If it has tripped, examine the pump for any faults and replace it if necessary. If the circuit breaker is fine, the pump motor may have failed, requiring pump replacement.
Why won't the fan start on my Seeley Breezair EXT Accessories cooler?
If your Seeley Accessories cooler fan won't start, begin by checking the main power circuit breaker and reset it if it has tripped after checking for the cause of overload. If the breaker is not the issue, the fan motor may be burned out and require replacement. Low system voltage or controller failure could also be responsible and you may need to consult with the power supply authority or replace the controller.
What to do if Seeley Breezair EXT cooler pump runs but no water?
If the pump in your Seeley Accessories cooler runs but no water circulates, first, adjust the float level to ensure there's sufficient water in the tank. Next, check for and clear any blockages in the water hoses or the pump strainer. Also, verify that the water supply pressure is adequate. Finally, make sure the water solenoid is installed correctly, ensuring it's aligned with the correct water flow direction.
How to stop continuous overflow of water in Seeley Accessories?
If your Seeley Accessories cooler is continuously overflowing water, the float valve adjustment may not be correct; try adjusting it. Alternatively, heavy pad deposits could be the cause; in this case, clean or replace the pads.
Why is water entering the Seeley Breezair EXT Accessories cooler outlet?
If water is entering the outlet of your Seeley Accessories cooler, start by tightening any loose water hose connections. If that doesn't solve the issue, inspect the water hoses for breaks and replace any cracked or broken ones. Also, ensure the float valve has its cover fitted; if not, replace the float valve. Check that the pads are correctly fitted into the pad frames and install the pad frame correctly. Finally, inspect the pads themselves; incorrect or damaged pads should be replaced with new Chillcel pads.
Why does my Seeley Breezair EXT Accessories cooler smell unpleasant?
If your Seeley Accessories cooler emits an unpleasant odor, it could be due to several reasons. New cooler pads often have an initial odor; to resolve this, fill the tank, run the pump briefly to wash the pads, drain the tank, and repeat as needed. This odour will dissipate after a number of hours of operation. Ensure the cooler isn't located near any sources of unpleasant odors; if it is, remove the source or relocate the cooler. Algae growth in the tank water can also cause odors; drain the tank, clean it thoroughly with a strong cleansing agent, refill it, and change the pads. If the pads remain wet after shutdown, run the fan on 'vent' for 10 minutes after the cooling cycle to dry them out. Heavy pad deposits can also contribute to odors, so clean or replace the pads.
Why is my Seeley Breezair EXT cooler not cooling enough?
If your Seeley Accessories cooler isn't cooling adequately, several factors could be at play. First, the cooler itself or the ducts might be too small for the space; in this case, consider replacing the cooler with a larger one or redesigning the ducting and outlets to ensure they're appropriately sized. Second, check the cooling pads for clogs or dirt and clean or replace them as needed. Also, ensure the pads are adequately wet and that the water distribution system is free of obstructions. For LPQI models, examine the lid water distribution channels for blockages. Finally, ensure there's sufficient ventilation to exhaust stale air; otherwise, high humidity may reduce cooling effectiveness. On days with excessive ambient humidity, the cooler's performance will be limited, and shutting off...
Understand and follow all safety precautions before operating or installing the cooler.
Key safety warnings to prevent fire, electric shock, or injury.
Outlines health and safety duties for those involved in installation and maintenance.
Guidance on conducting risk assessments for installation and maintenance tasks.
Practical considerations for safe access and operation at height.
Essential requirements for correct installation and operation.
Understand and follow all safety precautions before operating or installing the cooler.
Determine the optimal placement for the cooler, considering regulations and site conditions.
Proper installation and sealing of the roof jack for secure mounting.
Method for attaching and securing the cooler's leg supports to the roof.
Function and operation of the weatherseal for protection against wind.
Specifications for water supply, pressure, and temperature for cooler operation.
Guidelines for safe and compliant electrical connections and wiring.
Visual representations of electrical connections for different configurations.
Procedure for verifying motor current draw for optimal performance.
Completing all checks and ensuring the cooler is ready for use.
Importance of site cleanup after installation is completed.
Instructions for the customer on cooler operation and maintenance.
List and identification of all parts included in the cooler's packaging.
Site selection criteria for optimal cooler placement and performance.
Ensuring adequate space for future maintenance and repairs.
Safe procedures for moving the cooler unit to its installation location.
Steps for fitting and securing the roof jack adaptor.
Method for attaching the cooler unit to the roof dropper.
Detailed instructions for properly fastening the cooler's leg supports.
Operation and function of the weatherseal locking mechanism.
Essential specifications for the cooler's water supply connection.
Guidance on connecting the water supply to the cooler's inlet.
Explanation of the multi-function bleed-off fitting.
Adjusting the water level in the tank for correct operation.
Compliance with local regulations for electrical installation.
Diagrams illustrating different cooler wiring configurations.
How to set motor amps to nameplate level for full cooling capacity.
Procedure for adjusting the motor pulley to set fan speed and amps.
Importance and method of setting correct belt tension for optimal performance.
Steps to reset the pump circuit breaker if it trips.
Information on adjusting the bleed rate for salt deposit management.
How to operate the evaporative cooler effectively.
Step-by-step guide to initiating cooler operation.
Compliance with regional health standards for air quality and servicing.
Safety precautions and clearances required for maintenance.
Recommended service checks and frequency for residential units.
Pre-operation checks related to the cooler's installation.
Routine checks to ensure proper cooler functioning.
Specific maintenance for units with bleed systems.
Logbook for recording residential cooler maintenance activities.
Service intervals for commercial and industrial installations.
Continuation of maintenance schedule for commercial units.
Extra maintenance for heavily used coolers.
Logbook for commercial cooler maintenance records.
Adjusting the float valve for correct water level.
Procedure for reinstalling cooling pads after maintenance.
Verifying pump operation and water distribution.
Overall checks and final setup steps for the cooler.
A checklist to ensure all commissioning steps are verified.
Troubleshooting steps for when the cooler is not cooling effectively.
Diagnosing and resolving unusual noise from the cooler.
Solutions for pump malfunction or failure to start.
Steps to address issues with the fan not operating.
Diagnosing water flow issues to the pads.
Identifying and fixing causes of constant water overflow.
Troubleshooting water leaks from cooler outlets.
Steps to eliminate or reduce unpleasant smells from the cooler.
General| Brand | Seeley |
|---|---|
| Model | Breezair EXT |
| Category | Accessories |
| Language | English |
To Next Page
