Need help?Do you have a question about the Sennheiser XS WIRELESS 1 and is the answer not in the manual?
General| Transmitter Power | 10 mW |
|---|---|
| Receiver Type | Diversity Receiver |
| Modulation | FM |
| Switching Bandwidth | Up to 24 MHz |
| THD | < 0.9% |
| Audio Output Level (Jack) | +6 dBu |
| Frequency Range | 470 - 865 MHz |
| Transmission Range | Up to 75 meters |
| Operating Temperature | 0 °C to 40 °C |
| Wireless Range | Up to 75 meters |
| Operating Frequency Range | 548-572 MHz |
An overview of the XS Wireless product series, including links to specific sections.
Details on the physical connections and controls of the EM-XSW 1 rack receiver.
Step-by-step guide for connecting and disconnecting the power supply unit.
Instructions on how to output audio signals via XLR and jack sockets.
Procedures for turning the receiver on, to standby, and completely off.
Explanation of the status information shown on the receiver display.
How to navigate and adjust settings using the receiver's front panel buttons.
Steps to manually select a frequency bank and channel.
How to control the audio output volume using the VOL+/VOL- buttons.
Configuration options on the rear panel, including signal type and squelch.
Guidelines for setting up multiple receivers for intermodulation-free operation.
Details on the physical connections and controls of the dual rack receiver.
Step-by-step guide for connecting and disconnecting the power supply unit.
Instructions on how to output audio signals for each channel.
Procedures for turning the dual receiver on, to standby, and off.
Explanation of the status information shown on the dual receiver's display.
How to navigate and adjust settings using the dual receiver's front panel buttons.
Steps to manually select a frequency bank and channel.
How to control the audio output volume using the VOL+/VOL- buttons.
Configuration options on the rear panel, including signal type and squelch.
Guidelines for setting up multiple receivers for intermodulation-free operation.
Details on the physical connections and controls of the EM-XSW 2 rack receiver.
Instructions for connecting the rod antennas to the EM-XSW 2 receiver.
Instructions on how to output audio signals via XLR and jack sockets.
Guidelines and cautions for mounting the receiver in a rack.
Procedures for turning the receiver on, to standby, and completely off.
Explanation of the status information shown on the receiver display.
How to navigate and adjust settings using the front panel buttons.
How to perform an automatic frequency scan.
How to set the radio frequency by selecting a preset channel.
How to manually set the radio frequency independently of preset channels.
How to control the audio output volume using the VOLUME control knob.
Configuration options on the rear panel, including signal type and squelch.
A general overview of the SKM 825, 835, and 865 handheld transmitter models.
Guide on how to install and remove batteries from the handheld transmitter.
Explanation of battery charge status indicators on the display.
Steps to power the handheld transmitter on and off.
Information on how to establish a radio link by synchronizing transmitter and receiver.
Explanation of the information shown on the transmitter display.
How to adjust the audio signal level sent to the receiver.
How to mute or activate the audio signal using the mute switch.
A general overview of the SK-XSW bodypack transmitter.
Guide on how to install and remove batteries from the bodypack transmitter.
Explanation of battery charge status indicators on the display.
How to connect a microphone to the bodypack transmitter's input.
How to connect instruments or line sources to the bodypack transmitter.
Steps to power the bodypack transmitter on and off.
Information on how to establish a radio link by synchronizing transmitter and receiver.
Explanation of the information shown on the transmitter display.
How to adjust the audio signal level sent to the receiver.
How to mute or activate the audio signal using the mute switch.
Procedure to find and set an available radio frequency on the receiver.
Steps to establish a radio link by synchronizing receiver and transmitter.
Instructions for cleaning the microphone's sound inlet basket and foam insert.
Instructions for cleaning the bodypack transmitter contacts with a dry cloth.
General system specifications including modulation, bandwidth, and frequencies.
Technical specifications for the EM-XSW 1 stationary receiver.
Technical specifications for the EM-XSW 1 DUAL rack receiver.
Technical specifications for the EM-XSW 2 stationary receiver.
Technical specifications for the SKM-XSW handheld transmitter.
Technical specifications for the SK-XSW bodypack transmitter.
Specifications for ME 2-2, ME 3-II, and e 908T microphones.
Technical specifications for the NT 12-5 CW power supply unit.
Information on how to get technical support for the product.
How to provide feedback or suggestions on the instruction manual.
To Next Page
