Sensaphone 1104

To Next Page

To Previous Page

2. Press VOICE REPS.

The Model 1104 will recite the number programmed.

VOICE

REPS

Chapter 4: Communications Programming

Main Page

Important Safety Instructions3
- Fcc Requirements5
- Canadian Department of Communications Statement7
- Table of Contents9
Chapter 1: Introduction13
- Technical Support14
Chapter 2: Installation15
Operating Environment15
Mounting15
Power Surge Protection16
Power Supply and Battery Backup16
Starting the Model 110417
Run Mode and Standby Mode17
Telephone Line18
The Microphone19
Alert Inputs19
Installing the Sensor20
Multiple Sensors21
Outdoor Wiring22
Disconnecting the Model 1104 for Storage or Seasonal Use23
Chapter 3: Quick Start25
The Local Keypad25
Preparation for Programming25
Quick-Start Programming Steps26
- Step 1: Set Configuration of Inputs26
- Step 2: Set the ID Number27
- Step 3: Set Dial-Out Telephone Numbers28
- Step 4: Set Temperature Limits29
- Summary of the Alarm Dial-Out Process32
Chapter 4: Communications Programming33
The Unit ID Number33
- Programming the ID Number33
- Interrogating the ID Number34
Dial-Out Telephone Numbers35
- Programming Dial-Out Telephone Numbers35
- Interrogating a Dial-Out Telephone Number36
- Erasing a Telephone Number36
Tone or Pulse Dialing38
Special Dialing38
- Special Dialing Keys38
- Incorporating a Pause39
- Incorporating a Pound (#) or Asterisk (*)40
- Special Dialing to a Beeper or42
Rings until Answer44
- Programming Rings until Answer44
- Interrogating Rings until Answer44
TAD (Telephone Answering Device)45
- TAD Enable/Disable45
- Using the TAD Feature45
- No TAD in Use46
Listen-In Time47
- Programming the Listen-In Time47
- Interrogating the Listen-In Time48
- Call Delay49
- Programming the Call Delay49
- Interrogating Call Delay50
- Local Voice Mute51
- Enable/Disable Local Voice Mute51
Voice Repetitions52
- Programming Voice Repetitions52
- Interrogating Voice Repetitions52
- Intercall Time54
- Programming Intercall Time54
- Interrogating Intercall Time55
- Maximum Number of Calls (Max Calls)56
- Programming Max Calls56
- Interrogating Max Calls57
The Clock58
- Setting the Clock58
- Interrogating for the Current Time59
The Security Code60
- Locking the Keypad60
- Unlocking the Keypad60
Chapter 5: Alarm Programming63
Input Configuration63
- Programming Input Configuration64
- Verifying Input Configuration65
Enable/Disable Inputs65
- Changing Enabled/Disabled Input Status65
- Verifying Enabled/Disabled Input Status65
Input Recognition Time66
- Programming Input Recognition Time66
- Interrogating Input Recognition Time67
Establishing High and Low Temperature Limits69
- Programming Temperature Limits for a Selected Input69
- Disabling Alarm Response to High or Low Temperature70
- Interrogating High and Low Temperature Limits70
Temperature Scale71
- Temperature Calibration71
- Programming Temperature Calibration72
- Interrogating Temperature Calibration72
Obtaining Current Temperature73
AC Power Monitoring Enable/Disable74
- Enabling/Disabling the AC Power Alarm74
AC Power Failure Recognition Time74
- Programming Power Failure Recognition Time75
- Interrogating Power Failure Recognition Time76
- Sound Alarm Monitoring77
- Programming Sound Alarm Sensitivity77
- Interrogating Sound Sensitivity78
- Programming High Sound Alarm78
- Recognition Time78
High Sound Alarm Enable/Disable79
- Changing Enabled/Disabled High Sound Alarm79
Exit Delay80
Chapter 6: Acknowledgment, Status Report & Remote Access81
Alarm Acknowledgment81
- Local Acknowledgment81
- Touch-Tone™ Acknowledgment81
- Callback Acknowledgment82
Status Report83
- Example: Status Report, no Alarms83
- Example: Status Report, Existing Alarms84
- Example: Status Report, Disabled Inputs85
- Battery Condition85
- Remote Access by Touch-Tone™ Telephone86
Chapter 7: Operation89
Alarm Detection, Dial-Out and Acknowledgment89
Example: a Dial-Out Telephone Call94
Appendix A: Troubleshooting95
- Temperature Monitoring99
- Sound Level Monitoring100
- Other Monitoring102
Appendix B: Weekly Testing Procedure103
Appendix B: Checking Your Sensaphone for Proper Operation103
Appendix C: Accessories105
Appendix D: Returning the Unit for Repair107
- Service Department107
- Warranty108

Sensaphone 1104 - Page 53

Table of Contents