To Next Page
L
Linda DominguezSep 5, 2025
Why is there oil dripping from my Shark SGP-353037 Pressure Washer?
- Rrobert77Sep 5, 2025
Oil dripping from your Shark Pressure Washer usually indicates a worn oil seal. Check and replace it if necessary.
Why is there oil dripping from my Shark SGP-353037 Pressure Washer?
Oil dripping from your Shark Pressure Washer usually indicates a worn oil seal. Check and replace it if necessary.
What to do if my Shark SGP-353037 burner will not light?
If the burner on your Shark Pressure Washer won't light, start by checking the fuel level and ensuring you're using the correct fuel without water contamination. Next, inspect the fuel line for clogs and replace the fuel filter if it's plugged. Other potential causes include misadjusted burner air bands (readjust them), low fuel pressure from the fuel pump (increase pressure or replace the pump), a faulty burner transformer (test and replace if needed), disconnected or shorted electrical wiring (ensure all contacts are clean and tight), a slipping flex coupling (replace if needed), a defective ON-OFF switch (check for current and replace if needed), heavy sooting on the coil and burner (clean as required), improper electrode setting (check and reset), a tripped 25 amp circuit breaker (push...
What to do if there is water in the oil of my Shark SGP-353037 Pressure Washer?
If you notice water in the oil of your Shark Pressure Washer, there are a few potential causes. The oil seal might be worn, so check it and replace it if necessary. High air humidity can also contribute to this issue, in which case you should check and change the oil twice as often. Lastly, worn or bad packing could be the cause, so inspect it and replace it if necessary.
How to fix a Shark SGP-353037 burner that will not light?
If the burner of your Shark Pressure Washer won't light, it might be due to the following reasons: * The burner nozzle could be clogged and requires cleaning. * The thermostat may have malfunctioned, requiring testing and replacement if needed. * The fuel solenoid may have malfunctioned, also requiring testing and replacement if necessary.
What to do if the water temperature is too hot in my Shark SGP-353037?
If the water temperature of your Shark Pressure Washer is too hot, there are several potential reasons. The incoming water might be too warm, requiring you to lower its temperature. The fuel pump pressure could be too high, so you should call your local dealer for proper fuel pressure. The fuel pump itself might be defective, necessitating a replacement. An incorrect fuel nozzle size could also be the cause; check the parts breakdown or serial plate for the proper size. Insufficient water supply could be another issue, so check the water GPM to the machine. Lastly, restricted water flow could be the problem; inspect the nozzle for obstructions and ensure it's the correct size by checking the serial plate.
Why won't the burner motor run on my Shark Pressure Washer?
If the burner motor won't run on your Shark Pressure Washer, it could be due to a seized fuel pump (replace the fuel pump), a loose or misaligned burner fan (position correctly and tighten the set screw), a defective control switch (replace the switch), a loose wire (check and replace or tighten the wiring), or a defective burner motor (replace the motor).
What causes presence of water in oil in my Shark SGP-353037?
The presence of water in the oil of your Shark Pressure Washer can be due to a worn oil seal (check and replace if necessary), high air humidity (check and change oil twice as often), or worn or bad packing (check and replace if necessary).
What causes excessive vibration in the delivery line of my Shark SGP-353037 Pressure Washer?
Excessive vibration in the delivery line of your Shark Pressure Washer is caused by valves functioning irregularly. Check and replace if necessary.
Why is my Shark SGP-353037 Pressure Washer pump running normally but pressure is low on installation?
If your Shark Pressure Washer pump is running normally but the pressure is low upon installation, it could be due to the pump sucking air (check water supply and possibility of air seepage), sticking valves (check and clean or replace), a faulty unloader valve seat (check and replace), an incorrectly sized nozzle (check and replace, see serial plate for proper size), or a worn packing piston (check and replace).
Why is my Shark SGP-353037 operating at low pressure?
Low operating pressure in your Shark Pressure Washer can stem from several causes. Check if the water supply is sufficient, using a larger supply hose and cleaning the filter at the water inlet. Inspect the spray nozzle for wear or if it's the correct type for your machine, replacing it if necessary. Other potential issues include a slipping belt (tighten or replace it), leaks in the plumbing or hose (check and retape with Teflon tape), a faulty or misadjusted unloader (adjust or replace it), worn packing in the pump (install a new kit), obstructions in the spray nozzle (remove the obstruction), a leaking steam pressure control valve (rebuild or replace), slow engine RPM (set to proper specifications), or fouled or dirty inlet/discharge valves (check these valves).
Machine exceeds 85 dB, requiring ear protection.
High-pressure spray hazards require eye, hand, and foot protection.
Read manual, know controls, stay alert, avoid electrical hazards.
Precautions for refueling and operating near flammable materials.
Warnings about hot surfaces and the need to protect the machine from freezing.
Warning about hot discharge fluid and avoiding contact.
Caution regarding ladder use and operating on inclines.
Guidelines on avoiding acids, running dry, hose protection, and fatigue.
Steps for connecting the high-pressure hose, spray gun, and nozzles.
Connecting the garden hose to the cold water source and pump inlet.
Instructions for checking engine oil and filling the gas tank.
Connecting water and bleeding air from the system.
Steps for setting the fuel valve and choke for starting.
Turning the engine to run, pulling the starter grip, and adjusting choke.
Adjusting temperature and activating the burner for hot water.
Guide to different color-coded nozzles for various spray patterns.
Explanation of the pump protector mechanism and its function.
Procedures for cleaning surfaces and recommendations for best results.
How to apply detergent and rinse the cleaned surface.
Steps for safely shutting down the pressure washer and releasing pressure.
Guidelines for storing the machine to prevent damage, especially from freezing.
Procedures for engine maintenance before extended storage.
Possible causes and solutions for low pressure.
Troubleshooting steps for when the burner fails to light.
Causes and solutions for the machine smoking.
Issues related to the detergent not being drawn properly.
Troubleshooting for pump running issues, noise, and vibration.
General| Brand | Shark |
|---|---|
| Model | SGP-353037 |
| Category | Pressure Washer |
| Language | English |
