E
Evan CarsonSep 5, 2025
Why is there oil dripping from my Shark SGP-302517 Pressure Washer?
- JJustin MontgomerySep 5, 2025
Oil dripping from your Shark Pressure Washer usually indicates a worn oil seal. Check and replace it if necessary.
To Next PageTo Next PageWhy is there oil dripping from my Shark SGP-302517 Pressure Washer?
Oil dripping from your Shark Pressure Washer usually indicates a worn oil seal. Check and replace it if necessary.
What to do if my Shark Pressure Washer burner will not light?
If the burner on your Shark Pressure Washer won't light, start by checking the fuel level and ensuring you're using the correct fuel without water contamination. Next, inspect the fuel line for clogs and replace the fuel filter if it's plugged. Other potential causes include misadjusted burner air bands (readjust them), low fuel pressure from the fuel pump (increase pressure or replace the pump), a faulty burner transformer (test and replace if needed), disconnected or shorted electrical wiring (ensure all contacts are clean and tight), a slipping flex coupling (replace if needed), a defective ON-OFF switch (check for current and replace if needed), heavy sooting on the coil and burner (clean as required), improper electrode setting (check and reset), a tripped 25 amp circuit breaker (push...
What to do if there is water in the oil of my Shark SGP-302517?
If you notice water in the oil of your Shark Pressure Washer, there are a few potential causes. The oil seal might be worn, so check it and replace it if necessary. High air humidity can also contribute to this issue, in which case you should check and change the oil twice as often. Lastly, worn or bad packing could be the cause, so inspect it and replace it if necessary.
How to fix a Shark SGP-302517 burner that will not light?
If the burner of your Shark Pressure Washer won't light, it might be due to the following reasons: * The burner nozzle could be clogged and requires cleaning. * The thermostat may have malfunctioned, requiring testing and replacement if needed. * The fuel solenoid may have malfunctioned, also requiring testing and replacement if necessary.
What to do if the water temperature is too hot in my Shark SGP-302517?
If the water temperature of your Shark Pressure Washer is too hot, there are several potential reasons. The incoming water might be too warm, requiring you to lower its temperature. The fuel pump pressure could be too high, so you should call your local dealer for proper fuel pressure. The fuel pump itself might be defective, necessitating a replacement. An incorrect fuel nozzle size could also be the cause; check the parts breakdown or serial plate for the proper size. Insufficient water supply could be another issue, so check the water GPM to the machine. Lastly, restricted water flow could be the problem; inspect the nozzle for obstructions and ensure it's the correct size by checking the serial plate.
Why won't the burner motor run on my Shark SGP-302517?
If the burner motor won't run on your Shark Pressure Washer, it could be due to a seized fuel pump (replace the fuel pump), a loose or misaligned burner fan (position correctly and tighten the set screw), a defective control switch (replace the switch), a loose wire (check and replace or tighten the wiring), or a defective burner motor (replace the motor).
What causes presence of water in oil in my Shark Pressure Washer?
The presence of water in the oil of your Shark Pressure Washer can be due to a worn oil seal (check and replace if necessary), high air humidity (check and change oil twice as often), or worn or bad packing (check and replace if necessary).
What causes excessive vibration in the delivery line of my Shark Pressure Washer?
Excessive vibration in the delivery line of your Shark Pressure Washer is caused by valves functioning irregularly. Check and replace if necessary.
Why is my Shark SGP-302517 Pressure Washer pump running normally but pressure is low on installation?
If your Shark Pressure Washer pump is running normally but the pressure is low upon installation, it could be due to the pump sucking air (check water supply and possibility of air seepage), sticking valves (check and clean or replace), a faulty unloader valve seat (check and replace), an incorrectly sized nozzle (check and replace, see serial plate for proper size), or a worn packing piston (check and replace).
Why is my Shark SGP-302517 operating at low pressure?
Low operating pressure in your Shark Pressure Washer can stem from several causes. Check if the water supply is sufficient, using a larger supply hose and cleaning the filter at the water inlet. Inspect the spray nozzle for wear or if it's the correct type for your machine, replacing it if necessary. Other potential issues include a slipping belt (tighten or replace it), leaks in the plumbing or hose (check and retape with Teflon tape), a faulty or misadjusted unloader (adjust or replace it), worn packing in the pump (install a new kit), obstructions in the spray nozzle (remove the obstruction), a leaking steam pressure control valve (rebuild or replace), slow engine RPM (set to proper specifications), or fouled or dirty inlet/discharge valves (check these valves).
General| Brand | Shark |
|---|---|
| Model | SGP-302517 |
| Category | Pressure Washer |
| Language | English |
