Watching TV
Preparation
• POWER indicator (Green): The TV is on. ("Please wait"
will appear for a few seconds on the screen.)
Turning.on.the.power
Press
POWER
on
the TV,
or
POWER
on the remote
control.
TV
status
indicator
(POWER)
Perform the following steps before you press POWER
on the remote control unit.
1 Insert the batteries into the remote control unit.
(See page 8.)
2 Connect the antenna cable to the TV. (See page
12.)
3 Plug in the
AC
cord to the AC outlet. (See page 7.)
To
select a 4-digit channel number (e. g., Channel 22.1):
Press
2~2~
• (DOT)
~1
To select a 3-digit channel number (e. g., Channel 115):
Press
1~1~5
Method
2
Using remote control buttons
0-9, • (DOT)
to
select
channels for VHF/UHF/CATV/DIGITAL, then press
ENT
or
ENTER.
Changing channels
To select a 1
or
2-digit channel number (e. g., ChannelS):
Press 5
Turning offthe power
Press POWER on the TV,
or
POWER on the remote
control.
• The TV enters standby mode and the image on the screen
disappears.
• The POWER indicator
on
the TV changes to off.
RmD
• If you are not going
to
use this TV for a long period of time,
be
sure to remove the
AC
cord from the power outlet.
• Weak electric power
is
still consumed even when POWER
is turned off.
You can change channels
in
several ways.
Method
1
Using CH
+/-
or
A/Von
the remote control unit
or
on
the TV.
RmD
• If your cable-TV system includes analog and digital
channels using the same channel number, your channel
up function will scroll through the analog channel first,
then the digital channel. Although
it
may appear
as
though
the channel does not change, it actually moves from the
analog to the digital channel
in
sequence.
If you use channel-down,
it
will move
in
reverse, from the
digital channel
to
the analog channel.
RmD
• When selecting a 1-digit channel number, it
is
not
necessary to press 0 before the number.
• When you enter
0-9
only, channel selection will
be
made
if
there
is
no
operation within a few seconds.
RmD
• When you enter
0-9
only, channel selection will
be
made
if there
is
no operation within a few seconds.
• If you press 0
by
itself
in
"Air" reception, nothing will
happen.
• Complete the above steps within a few seconds.
• When you enter
0-9
and • (DOT), channel selection will
be
made if there
is
no
operation within a few seconds.
Lighting (Green)
OFFOFF/Standby
ON
A"toSetup
The
Auto Setup menu appears the first time you
turn on the TV, and assists you to select the menu
language, specify the Air/Cable setting, and program
your channels automatically.
IMPORTANT:
Make
sure that the antenna
or
cable TV
system connection is made!
1 The turn on the
TV,
press POWER (POWER indicator on
the front of the unit changes green.
It
may take approx.
10 seconds for a picture to appear on screen.).
2 The "Auto Setup" function begins. Press
~/~
to select
your desired language.
3 Press Ji,,/T
to
select "Signal Type", then press
~/~
to
select "Cable" or ''Air''.
Air: VHF/UHF channels
Cable:
CABLE TV channels
4 Press Ji,,/T to select "Automatic Search", then press
~
or
ENTER.
5 The TV will begin memorizing all the channels available
in
your area.
•
It
may take from 15 minutes to 30 minutes to complete
memorizing digital cable channels.
Depending on the reception condition, a bar display
may not advance for several minutes, please
be
patient.
RmD
•
If
you press ENTER
in
the process of "Auto Setup", the
Auto Setup stops and changes
to
the normal screen.
• When you make a menu selection, your changes occur
immediately.
You
do not have to press EXIT
to
see your
changes.
@-18
To Next Page
Loading...
