To Next PageTo Next PageWhy is there no sound from my Sharp Aquos LC-26GD7E LCD TV speakers?
If you are not getting any sound from your Sharp LCD TV speakers, check if “Dolby Digital” is selected in the “Language/sound selection” menu. If it is, connect the DIGITAL (SPDIF) OUT output to an external AV receiver or change the settings in the language/sound selection menu.
What to do if my Sharp Aquos LC-26GD7E LCD TV says 'No signal'?
If your Sharp LCD TV displays a 'No signal' message, it could be due to several reasons: * The antenna cable may not be connected properly. Ensure it is connected to the correct socket (SAT A/D). * The antenna system settings might be incorrect. Verify and adjust your settings. * The satellite antenna alignment could be off, or there might be an obstruction such as ice or snow. Correct the alignment or clear any obstructions.
What to do if AV Link does not function on Sharp LCD TV?
If the AV Link is not functioning on your Sharp LCD TV, consider the following possible causes and solutions: 1. The Euro AV cable may not be fully wired. In this case, replace the Euro AV cable. 2. Some video recorders can only take over the stations during the first time the TV is operated. Restore the video recorder to its factory settings. 3. If terrestrial and cable programs are stored at program places greater than 99, resort the terrestrial and cable programs so that they are between 1 and 99.
What to do if my Sharp LCD TV displays 'Station coded'?
If your Sharp LCD TV shows a 'Station coded' message, it could be due to: * A missing or incorrectly plugged-in CI module. Ensure a suitable CI module is present and properly connected. * A missing smart card. Plug in the smart card. * The station might not be released.
What to do if the station overview doesn’t show any encoded stations on my Sharp Aquos LC-26GD7E LCD TV?
If the station overview on your Sharp LCD TV doesn't show any encoded stations, even with the CI module and smart card plugged in, it might be because the CI module and/or smart card are not correctly inserted. Plug in the module and card correctly and repeat the station search process.
How to fix incorrect characters in analogue teletext mode on Sharp Aquos LC-26GD7E?
If various characters are displayed incorrectly in analogue teletext mode on your Sharp LCD TV, it is possible that the wrong character set is selected in the teletext menu. To fix this, set the correct character set in the teletext menu under Setup – Character set: choose 'standard' or the appropriate character set.
Why is there no sound via external digital audio amplifier on Sharp Aquos LC-26GD7E?
If you're not getting sound through your external digital audio amplifier with your Sharp LCD TV, it could be due to: * The external digital audio amplifier not supporting the selected sound format. Set PCM stereo on the DVD player in the sound selection. Switch language/sound selection (green button) to Stereo in the DVB program on the TV set in the status display. * The TV set and external digital audio amplifier are not connected. Connect Digital-Out from the TV set to a Digital-In of the external audio amplifier and select the appropriate input on this.
What to do if I can't find new stations after changing the CI module and smart card on my Sharp LCD TV?
If you've changed the CI module and smart card but can't find the new provider's stations on your Sharp LCD TV, you need to carry out the station search process again.
How to fix no digital teletext on Sharp LCD TV (UK)?
To enable digital teletext on your Sharp LCD TV in the UK, turn off DVB subtitles.
General| Screen Size | 26 inches |
|---|---|
| Display Type | LCD |
| Resolution | 1366 x 768 |
| Brightness | 450 cd/m² |
| Contrast Ratio | 800:1 |
| HDMI Ports | 1 |
| Component Video Inputs | 1 |
| Composite Video Inputs | 2 |
| Aspect Ratio | 16:9 |
| Viewing Angle | 170° |
| Audio Output | 2 x 10W |
| Input Ports | HDMI, Component, Composite |
Safety warning regarding fuse replacement and plug modification.
Details wire colour coding for mains lead and correct terminal connection.
Specific instructions for safely moving the television set.
Introduces navigation through the TV's menu system using the remote control.
Guides through automatic tuning and storing of TV and radio stations.
Describes how to perform a new search for available TV and radio stations.
Explains how to adjust volume and other sound settings like bass and treble.
Guides on adjusting picture settings like contrast, colour, and sharpness.
How to navigate and utilize the EPG for program information and scheduling.
How to schedule recordings using a connected VCR or DVD recorder via EPG.
Instructions for using the analogue Teletext service for information.
Guides on connecting external devices like VCRs and DVD players.
How to program timer recordings using the TV or an external recorder.
Guides on connecting and configuring audio amplifiers or active speakers.
How to connect devices via HDMI for high-quality digital audio and video.
Connecting a PC or Set Top Box to use the TV as a monitor.
