Supplied accessories
Make sure the following accessories are provided with the product.
Remote control unit
(x1)
Page 8
"AAA" size battery
(x2)
Page 8
AC cord
(x
1)
Page 7
Cable clamp
(x
1)
Cable tie
(x
1)
Page 7
Stand unit
(x
1)
Page 6
Operation manual
(x
1)
• Always use the AC cord supplied with the 1V.
• AC cord enclosed
in
this product
is
for
11
0-125V.
In
using
it
on the 125-240V AC, please consult to the following.
SHARP ELECTRONICS CORPORATION, LATIN AMERICA GROUP
6100 Blue Lagoon Drive, Suite 150, Miami, Florida 33126, U.S.A.
QUICK REFERENCE
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area
to
lay the TV on. This will prevent it
from being damaged.
• Attach the stand
in
the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result
in
the TV falling over.
@)-
6
Confirm that there are 8 screws
(4
short
screws and 4 long screws) supplied with the
stand unit.
Attach the supporting post for the stand unit
onto the base using the box for the stand unit
as
shown below.
• The supporting post attaches
to
the base at
an
off-centered location on the base. Be sure
to attach the supporting post
in
the direction
indicated below and attach the stand to the
1V
with the wider side
of
the base facing forward.
Forward-.
CD
Insert the stand into the openings on the
bottom of the
N.
eg)
Insert and tighten the 4 short screws into
the 4 holes on the rear of the
N.
• To detach the stand, perform the steps
in
reverse order.
Supplied accessories
Make sure the following accessories are provided with the product.
Remote control unit
(x1)
Page 8
"AAA" size battery
(x2)
Page 8
AC cord
(x
1)
Page 7
Cable clamp
(x
1)
Cable tie
(x
1)
Page 7
Stand unit
(x
1)
Page 6
Operation manual
(x
1)
• Always use the AC cord supplied with the 1V.
• AC cord enclosed
in
this product
is
for
11
0-125V.
In
using
it
on the 125-240V AC, please consult to the following.
SHARP ELECTRONICS CORPORATION, LATIN AMERICA GROUP
6100 Blue Lagoon Drive, Suite 150, Miami, Florida 33126, U.S.A.
QUICK REFERENCE
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area
to
lay the TV on. This will prevent it
from being damaged.
• Attach the stand
in
the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result
in
the TV falling over.
@)-
6
Confirm that there are 8 screws
(4
short
screws and 4 long screws) supplied with the
stand unit.
Attach the supporting post for the stand unit
onto the base using the box for the stand unit
as
shown below.
• The supporting post attaches
to
the base at
an
off-centered location on the base. Be sure
to attach the supporting post
in
the direction
indicated below and attach the stand to the
1V
with the wider side
of
the base facing forward.
Forward-.
CD
Insert the stand into the openings on the
bottom of the
N.
eg)
Insert and tighten the 4 short screws into
the 4 holes on the rear of the
N.
• To detach the stand, perform the steps
in
reverse order.
To Next Page
Loading...
