(3) Adjusting copy density
Execute SIM 46-01. After warming up, the ready lamp comes on and
at the same time, the current exposure level is displayed on the
panel.
AE_3.0 [ XXX ]
N_3.0 [ XXX ]
P_3.0 [ XXX ]
SFTP_3.0 [ XXX ]
30~170
AE: Automatic mode
N: Manual mode
P: Photo mode
SFTP: Soft focus photo mode
The copy density mode can be selected by using the copy density
key. The value of current copy density mode is displayed in reverse
video in brackets.
A. Adjusting copy density in the manual/Photo/Soft
focus photo modes
1
Select the picture quality mode (ex. manual mode) in which you
want to adjust the copy density, with the copy density key.
AE_3.0 [ XXX ]
N_3.0 [ XXX ]
P_3.0 [ XXX ]
SFTP_3.0 [ XXX ]
30~170
2 Make a copy.
Make sure that the "4" of the Sharp test chart UKOG-0162FCZZ is
copied and the "3" is not copied.
(for the UKOG-0089CSZZ, the "0.3" should be copied and the
"0.2" not copied.)
When too light:
Increase the value displayed on the COPIES MADE display.
When too dark:
Decrease the value displayed on the COPIES MADE display.
The value can be set in the range of 30 ∼ 170. The greater the set
value is, the darker the density is.
3 Press the copy density key to select the mode to be adjusted next,
and perform the same adjustment procedures.
(When the above set value is entered with exposure 3, the other
exposure (density) set values are automatically set.
B. Auto mode copy density adjustment
1 Select the auto mode with the copy density key.
AE_3.0 [ XXX ]
N_3.0 [ XXX ]
P_3.0 [ XXX ]
SFTP_3.0 [ XXX ]
30~170
2 Make a copy.
Check that "4" of Sharp test chart (UKOG-0162FCZZ) is copied
and "3" is not copied.
("0.3" of UKOG-0089CSZZ is copied and "0.2" is not copied.)
When too bright:
Increase the set value displayed on the copy quantity display.
When too dark:
Decrease the set value displayed on the copy quantity display.
The value can be set in the range of 30 ∼ 170. The greater the set
value is, the darker the density is.
When the copy density is within the reference range, the image ad-
justment is completed.
Note 1: SIM 46-2 allows to set the exposure level adjustment value
in each mode individually. (Refer to the section of simula-
tions.)
(4) Image mode selection
Each image mode has two image expressions, which can be selected
with SIM 26-27.
When SIM 26-27 is executed, the following display is shown to allow
selection of 1 and 2 for each image mode.
SIMULATION NO.26-27
IMAGE DENSITY MODE SETTING
AUTO [X]:_1.(PEN) 2.(ORG)
MANUAL [X]:_1.(PEN) 2.(ORG)
PHOTO [X]:_1.(PHOTO1) 2.(PHOTO2)
SOFT_P [X]:_1.(SOFT_P1) 2.(SOFT_P2)
[|]KEY:MOVE PRINT SW:EXECUTE
Here are the characteristics of picture quality in each mode. Use them
as a rough guide.
(All the settings of picture quality are factory set for 1.)
12
Auto
Manual
Reproduction of
characters and fine lines
Enhancement of contours
Calmness
Photo Calmness Enhancement of contours
Reproduction of
characters
Soft focus
photo
Rough patterns
High gray scale level
Fine patterns
High density
The settings "1" and "2" can be selected according to the purpose.
(5) Selecting gray scale level
In SIM 46-7, it is possible to set the gray scale level in each picture
quality mode.
Execute SIM 46-7. The gray scale level adjustment value for each
picture quality mode appears. (The setting in each mode is factory set
for 10.)
SIMULATION NO.46-7
TONE ADJUSTMENT SETTING (COPY)
AUTO AE_3.0 (1~20) [XX]:XX
MANUAL N_3.0 (1~20) [XX]:XX
PHOTO P1_3.0 (1~20) [XX]:XX
SOFT_P SFT_3.0 (1~20) [XX]:XX
[|]KEY:MOVE PRINT SW:EXECUTE
The gray scale level is decreased by increasing the setting and in-
creased by reducing the setting. The adjustment range from 1 to 20.
3
4
5 62
Not copied
Copied
3
4
5 62
Not copied
Copied
6 – 3
To Next Page
Loading...
