Sharp AR-M316

AR-M256/M257/M258/M316/M317/M318/5625/5631 TROUBLE CODE LIST 9 - 5
F1 20 Content Alignment motor (R) trouble (AR-F14N)
Details Alignment motor operation abnormality
Cause Motor lock.
Motor rpm abnormality.
Overcurrent to the motor.
Finisher control PWB trouble.
Check
and
remedy
Use SIM3-3-7 to check the alignment (R)
motor operation
30 Content Finisher interface error (AR-F14N)
Details Communication line test error occurs when
power is turned on or after the exit of a
simulation mode.
Error in console finisher communication
Cause Connection trouble or disconnection of the
connector and harness between the body
and the finisher.
Finisher control PWB trouble.
Control PWB (PCU) failure.
Malfunction by noises.
Check
and
remedy
Canceled by turning OFF/ON the power.
Check the connectors and the harness of
communication line
Replace the finisher control PWB.
31 Content Fold sensor trouble (AR-F14N)
Details Sensor input value abnormality
Cause Sensor breakage.
harness breakage.
Finisher control PWB trouble.
Check
and
remedy
Use SIM3-2 to check the sensor operation.
32 Content Punch unit communication trouble
(AR-F14N)
Details Communication error between the console
finisher and the punch unit
Cause Improper connection or disconnection of
connector and harness between the
finisher and the punch unit.
Finisher control PWB trouble.
Control PWB (PCU) failure.
Malfunction by noises.
Check
and
remedy
Canceled by turning OFF/ON the power.
Check the connectors and the harness of
communication line.
Replace the finisher control PWB.
33 Content Punch side registration motor trouble
(AR-F14N)
Details Punch side registration motor operation
abnormality
Cause Motor lock.
Motor rpm abnormality.
Overcurrent to the motor.
Finisher control PWB trouble.
Check
and
remedy
Use SIM3-3-2 to check the punch side
registration motor operation
34 Content Punch motor trouble (AR-F14N)
Details Punch motor operation abnormality
Cause Motor lock.
Motor rpm abnormality.
Overcurrent to the motor.
Finisher control PWB trouble.
Check
and
remedy
Use SIM3-3-3 to check the punch motor
operation
Trouble
code
Details of trouble
Main
code
Sub
code
F1 35 Content Punch side registration sensor trouble
(AR-F14N)
Details Sensor input value abnormality
Cause Sensor breakage.
harness breakage.
Finisher control PWB trouble.
Check
and
remedy
Use SIM3-2 to check the punch side
registration sensor operation
36 Content Punch registration sensor trouble
(AR-F14N)
Details Sensor input value abnormality
Cause Sensor breakage.
harness breakage.
Finisher control PWB trouble.
Check
and
remedy
Use SIM3-2 to check the punch
registration sensor operation
37 Content Backup RAM trouble (AR-F14N)
Details Backup RAM contents are disturbed
Cause Finisher control PWB trouble.
Malfunction by noise.
Check
and
remedy
Replace the finisher control PWB.
38 Content Punch backup RAM trouble (AR-F14N)
Details Punch unit backup RAM contents are
disturbed.
Cause Punch control PWB trouble.
Malfunction by noise.
Check
and
remedy
Replace the punch control PWB
39 Content Punch dust sensor trouble (AR-F14N)
Details Punch dust sensor detection trouble
Cause Sensor breakage.
harness breakage.
Finisher control PWB trouble.
Check
and
remedy
Use SIM3-2 to check the punch dust
sensor operation
40 Content Punch power trouble (AR-F14N)
Details Panch unit power discontinuity detection
Cause Punch control PWB defect
Check
and
remedy
Replace the punch control PWB
50 Content Finisher incompatibility error
Details Speed does not coincide between finisher
and main unit
Cause AR-FN5N/F14 is connected to 31 sheet
model
Check
and
remedy
Connect AR-FN5A.
Connect AR-F14N.
53 Content Interface transport unit connection trouble
(AR-F14N)
Details Interface transport unit connector
disconnection
Cause Improper connection of connector between
the finisher and the interface transport unit
Check
and
remedy
Check the interface transport unit
connector.
Trouble
code
Details of trouble
Main
code
Sub
code