Sharp AR-M350U - Page 206

AR-M350 SIMULATIONS 10-62
<List of set values>
66-4
Purpose Operation test, check
Function (Content) Used to check the operation of data signal output
in the FAX data output mode.
(Used to check the MODEM operation.)
Send level 0db (Max.)
(Only when FAX is installed.)
Section FAX
Item Operation
Operation/Procedure Signal output check (level Max.)
When CUSTOM SETTING is pressed during
execution of this simulation, execution is
stopped.
Enter a number and press START to change the
signal.
SIMULATION 66-4
SIGNAL OUTPUT CHECK.(LEVEL MAX) SELECT 1-32, AND PRESS START.
1.NOSIGNAL 2.33.6 V343.31.2 V34 4.28.8 V34
5.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V3411.12.0 V3412.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V3318.14.4 V1719.12.0 V1720.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER32.No RBT
1
SIMULATION 66-4
SIGNAL OUTPUT CHECK.(LEVEL MAX) SELECT 1-32, AND PRESS START.
EXECUTING...
1.NOSIGNAL 2.33.6 V343.31.2 V34 4.28.8 V34
5.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V3411.12.0 V3412.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V3318.14.4 V1719.12.0 V1720.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER32.No RBT
1
SIMULATION 66-4
SIGNAL OUTPUT CHECK.(LEVEL MAX) SELECT 1-32, AND PRESS START.
EXECUTING...
1.NOSIGNAL 2.33.6 V343.31.2 V34 4.28.8 V34
5.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V3411.12.0 V3412.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V3318.14.4 V1719.12.0 V1720.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER32.No RBT
2
SIMULATION 66-4
SIGNAL OUTPUT CHECK.(LEVEL MAX) SELECT 1-32, AND PRESS START.
1.NOSIGNAL 2.33.6 V343.31.2 V34 4.28.8 V34
5.26.4 V34 6.24.0 V34 7.21.6 V34 8.19.2 V34
9.16.8 V34 10.14.4 V3411.12.0 V3412.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V3318.14.4 V1719.12.0 V1720.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER32.No RBT
2
Press [CUSTOM SETTING] key.
Press [START] key.
Press [CUSTOM SETTING] key.
Select 2 and press [START] key.
Same
display
1 No signal 17 12.0 V33
2 33.6 V34 18 14.4 V17
3 31.2 V34 19 12.0 V17
4 28.8 V34 20 9.6 V17
5 26.4 V34 21 7.2 V17
6 24.0 V34 22 9.6 V29
7 21.6 V34 23 7.2 V29
8 19.2 V34 24 4.8 V27t
9 16.8 V34 25 2.4 V27t
10 14.4 V34 26 0.3 FLG
11 12.0 V34 27 CED2100
12 9.6 V34 28 CNG1100
13 7.2 V34 29 0.3 V21
14 4.8 V34 30 ANSam
15 2.4 V34 31 RINGER
16 14.4 V33 32 No RBT
 ,+   !" #$%&'