AR-M350 SIMULATIONS 10-25
<List of set values>
<List of set values>
<List of set values>
<List of set values>
Main code 24
24-1
Purpose Data clear
Function (Content) Used to clear the misfeed counter, misfeed
history, trouble counter, and trouble history.
(After completion of maintenance, these
counters must be cleared.)
Section
Item Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
PAPER JAM Number of times of paper jam
SPF JAM Number of times of SPF jam
TROUBLE Number of times of troubles
24-2
Purpose Data clear
Function (Content) Used to clear the number of use (print quantity)
of each paper feed section.
Section Paper feed
Item Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1 Tray 1 use quantity
2 Tray 2 use quantity
3 Tray 3/LCC left tray use quantity
4 Tray 4/LCC right tray use quantity
5 Manual feed tray use quantity
6 Duplex paper feed use quantity
1
SIMULATION 24-1
PAPER JAM COUNTER DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO
1
SIMULATION 24-1
JAM/ TROUBLE COUNTER DATA CLEAR.SELECT1-3,AND
PRESS START.
1. PAPER JAM
2. SPF JAM
3. TROUBLE
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
1
SIMULATION 24-2
TRAY1 COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 24-2
PAPER FEED COUNTER DATA CLEAR.SELECT1-6,AND PRESS START.
1. TRAY1 2. TRAY2
3. TRAY3/LCC1 2. TRAY4/LCC2
5. BPT 6. ADU
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
24-3
Purpose Data clear
Function (Content) Used to clear the number of use of the staple,
DSPF and the scanner (reading) unit.
Section
Item Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1 SPF paper passing quantity
2 Number of times of document scan
3 Number of times of stapling
4 Number of times of punching
5 Number of times of finish stamp
24-4
Purpose Data clear
Function (Content) Used to reset the maintenance counter.
Section
Item Counter
Operation/Procedure Select with 10 digit key pad and press START
key.
The procedure below is executed and the display
returns to the original state.
1: Counter is cleared 2: Not cleared
1 maintenance counter
1
SIMULATION 24-3
SPF COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 24-3
ORG./STAPLE COUNTER DATA CLEAR.SELEC1-5, AND PRESS START.
1. SPF
2. SCAN
3. STAPLER
4. PUNCH
5. STAMP
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
1
SIMULATION 24-4
MAINTENANCE COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 24-4
MAINTENANCE COUNTER DATA CLEAR.PRESS START.
1. MAINTENANCE
Press [START] key.
Press [CUSTOM SETTING] key
or [START] key.
') !"# $%&
To Next Page
Loading...
