How to fix Sharp BD-HP22S remote control not working?
If the Sharp Blu-ray Player's remote control isn't working, try these steps: First, ensure you're within the operating range. If that doesn't work, replace the batteries. As a last resort, reset the remote by pressing and holding the '1' button and then the ENTER button together for more than 5 seconds.
Why is Sharp BD-HP22S audio reversed or only one side working?
If the left and right channels of audio are reversed, or sound comes out of only one side on your Sharp Blu-ray Player, check if the left and right audio cables are connected to the opposite terminal, or if one side is disconnected.
How to fix Sharp BD-HP22S Blu-ray Player widescreen video stretched?
If widescreen video appears vertically stretched, or black bands appear at the top and bottom of the screen on your Sharp Blu-ray Player, check if “TV Aspect Ratio” is set to match the connected TV. If you are using a widescreen TV, ensure the “TV Aspect Ratio” is set to “Wide”.
How to resolve no sound or distorted sound on Sharp Blu-ray Player?
If you are experiencing no sound or distorted sound on your Sharp Blu-ray Player, first, ensure the volume of the TV or amplifier is not set to minimum and increase it. Note that there is no sound during still mode, slow motion playback, fast forward, and fast reverse. If using DVD audio recorded in DTS, it is only output from the DIGITAL AUDIO OUT terminal, so connect a DTS compatible digital amplifier or decoder to the DIGITAL AUDIO OUT OPTICAL terminal on the player. Check that the audio cable is connected correctly and that the cable plugs are clean. You can also try taking out the disc and cleaning it. Audio may not be output depending on the audio recording status, such as when audio other than an audio signal or non-standard audio is recorded for the audio content of the disc.
Why is there just audio with no video on my Sharp Blu-ray Player?
If there is just audio with no video on your Sharp Blu-ray Player, check if the connection cable for video output is connected properly.
What to do if Sharp Blu-ray Player screen freezes?
If the screen freezes and the operation buttons do not work on your Sharp Blu-ray Player, press H STOP, then restart playback. If that doesn't work, turn the power off and then on again. If the power is not turned off, perform a reset. Also, check the condition of the disc to ensure it is not damaged or dirty.
What to do if Sharp Blu-ray Player disc is automatically ejected?
If your Sharp Blu-ray Player's disc is automatically ejected after closing the disc tray, make sure that the disc is loaded properly (aligned in disc tray and label-side up). Also, take out the disc and clean it. Verify that the region code on the disc matches that of the player and that the disc is playable.
Why does my Sharp Blu-ray Player power keep turning off?
If the Sharp Blu-ray Player automatically turns off, check if “Auto Power Off” is set to “Yes”. When “Auto Power Off” is set to “Yes”, the power will automatically turn off after 10 continuous minutes of inactivity (no playback).
How to fix Sharp Blu-ray Player power cannot be turned on?
If your Sharp Blu-ray Player won't turn on, ensure the power cord is securely plugged into the AC outlet. If it's plugged in, press and hold the B button on the player until “ ” appears on the front panel display. After the B (Standby/ On) indicator lights up, try turning on the power. You can also try pressing B after the B (Standby/On) indicator turns on.
General| Type | Blu-ray Player |
|---|---|
| Resolution | 1080p |
| Network Connectivity | Ethernet |
| BD-Live | Yes |
| HDMI Output | 1 |
| USB Port | 1 |
| Ethernet Port | 1 |
| Disc Playback | BD, DVD, CD |
| Video Output | HDMI |
| Audio Output | HDMI, Coaxial |
| Supported Formats | MPEG2, MPEG4 AVC, VC-1, AVCHD, JPEG, MP3 |
To Next Page
