In
thts
example,
the
clock
is
set for
the
24-hour
(0:OO)
system.
TUNING/’
I
TIME
MEMORY/
(,/fi)
SET
4
\\if/
I,
n
1-t
1-I
,-I
Cl
,i,!\
0:OO
-AM
12:OO
-
AM
0:OO
+ +
51
1
Press
the
ON/STAND-BY
button
to enter
the
stand-by
mode.
2
Press
the
CLOCK
button.
3
"
Within
5
seconds, press the MEMORY/SET
button.
4
Press
the
TUNINGmIME
(vor~)
button
to select
the
time
display
mode.
“0:00”
+
The 24.hour display
will
appear.
(0:OO
23:59)
“AM
1200’
+
The
la-hour
display
will
appear.
(AM or
PM
12:OO
11:59)
“AM
0:OO”
+
The 12-hour
display
will
appear.
(AM or
PM
0:OO
-
11:59)
0
Note that this
can
only
be
set
when
the
unit
is
first
installed
or
it
has
been
reset (see page
30).
5
Press
the
MEMORY/SET
button.
6
Press the TUNINGmIME
(
v
or
A)
button
to
adjust
the
hour.
0
Press
the
TUNlNGfllME
(v
or
A)
button
once to advance
the
time
by
1
hour.
Press for more
than
0.5
seconds
to
ad-
vance continuously.
0
When the 12.hour display
is
selected, “AM” will
change
auto-
matically
to
“PM”.
7
Press
the
MEMORY/SET
button.
8
Press
the
TUNING/TIME
(
v
or
F.
)
button to adjust the
minutes.
l
Press
the
button
for at least 0.5 seconds to change
the
time
in
5-minute intervals.
0
The
hour
setting
will
not advance even
if
minutes advance
from “59” to “00”.
9
Press
the
MEMORY/SET
button
l
The clock starts operating from “0’ seconds. (Seconds are
not
displayed.)
Note:
l
In
the
event
of
a power failure or when
the
AC power
lead
is
disconnected,
the
clock display
will
go
out.
When
the
AC power
supply
is restored,
the
clock display
will
flash
on
and
off
to
indicate
the
time when
the
power failure
occurred or
when
the AC power
lead
was disconnected.
If
this
happens,
follow
the
procedure below to change
the
clock
time.
To
change
the
clock
time:
When
the
unit
is
in
the
stand-by
mode
l
When
the
unit
is
in
the
demonstration
mode,
press
the
DEMO
button
to enter
the
clock
mode.
a
Press
the
MEMORY/SET
button
Q
Perform
steps
6
-
9
above.
When
the
unit
is
on:
(??
Press
the
CLOCK
button.
Q
Within
5
seconds,
press
the
MEMORY/SET
button
0
Perlorm
steps
6
-
9
above.
To
see
the
time
display:
Press
the
CLOCK
button.
l
The time display
will
appear for about
5
seconds
To
change
the
time
display
mode:
Q
Press
the
ON/STAND-BY
button
to
enter
the
stand-by
mode.
0
Whilst
pressing
down
the
VOLUME
v
button
and
the
TUN-
INGiTlME
A
button,
hold
down the ON/STAND-BY
button
for
at least
1
second.
Q
Periorm steps
6
-
9
above.
Caution:
l
The operatiow’explained above
will
erase
all
data stored
in
memory
including
clock
and
timer
settings,
and
tuner
and
CD
presets.
--1----
0.2
m
6
m
(6”
20’)
I
Notes
concerning
use:
l
Replace
the
batteries
if
the
operating distance becomes
re-
duced
or
if
operation becomes erratic.
l
Periodically clean the transmitter LED
on
the
remote control
and
the
sensor
on
the main
unit
with
a
soft
cloth.
l
Exposing
the
sensor
on
the
main
unit
to
strong
light
may
interfere
with
operation. Change
the
lighting
or
the
direction
of
the
unit.
l
Keep the remote control away from moisture, excessive
heat,
shock,
and
vibrations.
Reset
the
microcomputer
under
the
following conditions:
l
To erase
all
of
the
stored memory contents (clock
and
timer
settings,
and
tuner
and
CD presets).
l
If
the
display
is
not
correct.
l
If
the
operation
is
not
correct.
Note:
l
To erase
the
tuner preset memory see “To erase
all
of
the
contents of preset memory”
on
page
16.
1 Press
the
ON/STAND-BY
button
to enter
the
stand-by
mode
2
While
pressing
down
the
VOLUME
v
button
and
the
TUN-
INGRIME
A
button.
hold
down
the
ON/STAND-BY
button
for
at least
1
second.
To Next Page
Loading...
Need help?
General
