Sharp HT-SB100

7
NOTE:
ū The operational range between this player and a Bluetooth device is
approximately 8 meters (without any object between the Bluetooth
device and the unit).
ū Before you connect a Bluetooth device to this unit, ensure you know
the device’s capabilities.
ū Compatibility with all Bluetooth devices is not guaranteed.
ū Any obstacle between this unit and a Bluetooth device can reduce
the operational range.
ū If the signal strength is weak, your Bluetooth receiver may
disconnect, but it will re-enter pairing mode automatically.
1. While in ON mode, press
on the remote control or on the unit to
select Bluetooth mode. The indicator light will ash blue.
2. Activate your Bluetooth device and select the search mode.
“SHARP HT-SB100” will appear on your Bluetooth device list.
ū If you cannot nd the unit, press and hold
on the unit or on the
remote control.
3. Select “Sharp HT-SB100“ from the list of devices. An audio prompt
will sound when it has been successfully connected, and the
indicator will light a solid blue.
4. Begin playing music from the connected Bluetooth device.
To disconnect the Bluetooth function, you can:
ū Switch to another function on the unit.
ū Disable the Bluetooth function on your device. An audio prompt will
sound when it has been successfully disconnected.
ū Press and hold
on the unit or on the remote control.
TIPS:
• Enter “0000“ for the password if necessary.
• If no other Bluetooth device pairs with the soundbar in 2 minutes,
the soundbar will reconnect to the previous connection.
• The soundbar will also be disconnected when your device is moved
beyond the operational range.
• If you want to reconnect your device to this soundbar, place it
within the operational range.
• If the device is moved beyond the operational range, when it is
brought back, please check if the device is still connected to the
soundbar.
• If the connection is lost, follow the instructions above to pair your
device to the soundbar again.
Listen to music from Bluetooth device
ū If the connected Bluetooth device supports Advanced Audio
Distribution Prole (A2DP), you can listen to the music stored on the
device through the soundbar.
ū If the device also supports Audio Video Remote Control Prole
(AVRCP), you can use the soundbar‘s remote control to play music
stored on the device.
1. Pair your device with the soundbar.
2. Play music via your device (if it supports A2DP).
3. Use the supplied remote control to control play (if it supports
AVRCP).
ū To pause/resume play, press
on the remote control.
ū To skip to a track, press
/ buttons on the remote control.
USB operation
• Press on the soundbar repeatedly or on the remote control to
select USB mode. Connect the USB memory device containing MP3
les (ash drives up to 32GB supported).
• Press
to start playback.
• Turn o the soundbar before removing the USB memory device.
NOTE
SHARP will not be held liable for any loss of data while the USB
memory device is connected to this unit. Always back up your music
before playing on this product.
USB functions (remote control)
ū To play or pause.
ū
Skip to next song | Press and hold to fast forward.
ū
Skip to beginning of song | Press and hold to quickly rewind.
Troubleshooting
To keep the warranty valid, never try to repair the system yourself. If
you encounter problems when using this unit, review the following
before requesting service.
No power
Ensure that the AC cord is properly connected.
Ensure that there is power at the AC outlet.
Press standby button on the remote control or soundbar to turn the
soundbar on.
No sound
For HDMI ARC to work, ensure you are using HDMI version 1.4 or
higher.
Increase the volume. Press + on the remote control or on the
soundbar.
Press
on the remote control to ensure the soundbar is not muted.
Press
to select a dierent input source.
When connected to a digital source (HDMI or Optical), if there is no
audio:
ū Try setting the TV output to PCM or
ū Connect directly to your Blu-ray/other source, some TVs do not pass
through digital audio.
Your TV may be set to variable audio output. Conrm that the audio
output setting is set to FIXED or STANDARD, not VARIABLE. Consult
your TV’s user manual for more detailed information.
If using Bluetooth, ensure that the volume on your source device is
turned up and that the device is not muted.
Remote control does not work
Before you press any playback control button, rst select the correct
source.
Reduce the distance between the remote control and the unit.
Insert the battery with its polarities (+/-) aligned as indicated.
Replace the battery.
Aim the remote control directly at the sensor on the front of the unit.
I hear buzzing or humming
Ensure all cables and wires are securely connected.
Connect a dierent source device (TV, Blu-ray player, etc) to see if the
buzzing persists. If it does not, the problem may be with the original
device.
Connect your device to a dierent input on the soundbar.
I can’t nd the Bluetooth name of this unit on my
Bluetooth device
Ensure the Bluetooth function is activated on your Bluetooth device.
Re-pair the unit with your Bluetooth device.
This device is set to power o after 15 minutes of no
source signal
When the unit’s external input signal level is too low, the unit will be
turned o automatically in 15 minutes. Please increase the volume
level of your external device. This feature is a requirement of ERPII and
is designed to save energy when the Soundbar is not in use.