E-14
General control (continued)
Connecting the wireless Subwoofer
The sound bar and subwoofer will link automatically
(wirelessly) when turned on as it is already pre-linked at
the factory. If the link cannot be established, please set the
connection by the following method.
z During pairing process:
On remote control: “SW LINK” will appear.
On sound bar: indicator will blink in violet.
On subwoofer: indicator will blink in blue.
z When pairing is successful:
On remote control: “SW LINK” disappears.
On sound bar: indicator turns red.
On subwoofer: indicator turns blue.
During sound bar standby and subwoofer power off
mode (AC power cord unplugged):
1. Press and hold the PAIRING button on the sound bar
or PAIRING on the remote control for more than 3
seconds.
2. Within 2 minutes, press and hold the SW LINK button
on the subwoofer for more than 3 seconds.
z In case the link is still not established (Sound bar
indicator blinks), press and hold the SW LINK button
at the back of the subwoofer until sound bar indicator
lights up.
SW LINK
SW LINK
Sound bar Remote
Control
Subwoofer
Notes:
z If a device such as microwave oven, wireless LAN card,
Bluetooth device or any other device that uses the
same 2.4GHz frequency near the system, some sound
interruption may be heard due to interference.
z The transmission distance of the wireless signal
between the subwoofer and sound bar is about 32 feet
(10 meters), but may vary depending on your operating
environment. If a steel-concrete or metallic wall is
between the subwoofer and the sound bar, the system
may not operate at all, because the wireless signal
cannot penetrate metal.
Caution:
z Keep the subwoofer away from water and moisture.
z To get the optimum listening performance, make sure
the area around the sound bar and subwoofer is clear
of any obstacles.
To select a menu on the remote control
1. Press MENU button.
2. To select a menu, press or button, then press
button.
3. Press or button to select an option in the desired
menu.
4. To select another menu, press button and
repeat steps 2 to 3 above.
Menu/
Function
Level/Mode
3D AUDIO
3D AUDIO 1 2 OFF
AV SYNC
AV SYNC 0 1 2 3
APC
5 MIN 10 MIN 15 MIN 20 MIN
SW LEVEL
-5 -4 ..... +4 +5
ECO MODE ON
OFF
VERSION SOUND BAR
REMOTE CONTROL
Volume auto fade-in
If you turn off and on the sound bar with the volume set
to 80 or higher, the volume starts at 40 and fades in to
the last set level.
Volume control
Sound bar operation:
Press the VOLUME +
button to increase the
volume and the VOLUME –
button for decreasing.
MIN MAX
2 99
.....
1
Remote control operation:
Press the VOL. + button to increase the volume and the
VOL. – button to decrease the volume.
Sound Mode
To change to a different mode, press the SOUND MODE
button repeatedly on the sound bar or remote control
until the desired sound mode is displayed.
CINEMA (for cinema sound effect)
MUSIC (for standard sound effect)
GAME (for game sound effect)
SPORT (for sport broadcasting)
NEWS (for news)
NIGHT (for night)
BYPASS (for flat sound effect)
Muting
The volume is muted temporarily when pressing the
MUTE on the remote control. Press again to restore the
volume.
Note:
When the sound bar is turned off and back on again,
muting is canceled.
Bass and Treble Control (remote control)
Bass and Treble control is applicable during BYPASS
mode only.
Bass Control
1. Press the BASS/TREBLE button to select bass.
2. Within 5 seconds, press the VOL. (+ or –) button to
adjust the bass.
To Next Page
Loading...
Need help?
General
