Sharp LC-32LE225E - ETC, Public Mode, and Smart Loader Settings

23
LC-32LE225
Page Line Sub
Page
Item Description Remarks (adjustment details, etc.)
01/17 [SHARP FACTORY MENU
7 ETC EEP, Autoinstallation, Op-
tion, Country, L Error...
Press “OK” to enter to ETC Submenu
09/17 EEP Clear
Press “
►” to Clear NVM data
EEP Clear B
Press “
►” to Clear NVM data (except adjustments area).
Standby cause reset “OK“ will be displayed
Press “
►” to Reset of STANDBY CAUSE.
Autoinstallation SW Off
On: Pending to execute on next power on. Off: Not required.
Pattern 0 Selection of internal pattern from 0 up to 6…
L Error Reset 0
Press “
►” to LAMP ERR RESET. Initialization of L_ERR.
L Error Check On L_ERR detection. ON: activated. OFF: deactivated.
I2C OFF Off I2C BUS status. On: free BUS. Off: Normal.
Sharp protocol On Remote Control Protocol. On: SHARP Off: MSTAR.
8 PUBLIC MODE (1/2) PUBLIC MODE Submenu Press “OK” to enter to PUBLIC MODE Sub-
menu
10/17 Power On fi xed Variable
Press “
◄” or “►” to change Variable/Fixed.
Maximum volume 60
Press “
◄” or “►” to change 0/60.
Volume fi xed Variable
Press “
◄” or “►” to change Variable/Fixed.
Volume fi xed Level 20
Press “
◄” or “►” to change 0/60.
RC button Respond
Press “
◄” or “►” to change Respond/No respond.
Panel button Respond
Press “
◄” or “►” to change Respond/No respond.
Menu button Respond
Press “
◄” or “►” to change Respond/No respond.
On screen display On
Press “
◄” or “►” to change On/Off.
Input mode start Normal
Press “
◄” or “►” to change Normal/TV/SCART/…
Input mode fi xed Variable
Press “
◄” or “►” to change Variable/Fixed.
Input TV mode program
number
Normal
Press “
◄” or “►” to change Normal → 1 → 2 ...999
→ Normal).
RC path through Off
Press “◄” or “►” to change On/Off (required external
module)
PUBLIC MODE (2/2) PUBLIC MODE Submenu
11/17 Hotel mode Off
Press “
◄” or “►” to change On/Off.
Reset “OK“ will be displayed
Press “
◄” or “►” to return to factory settings.
Execute “OK“ will be displayed
Press “
◄” or “►” to confirm.
9 SMART LOADER SMART LOADER Sub-
menu
Press “OK” to enter to SMART LOADER Sub-
menu
12/17 Save settings to USB (“OK“ or “NO USB drive
available, please check
and/or insert USB dri...”
will be displayed).
Press “
◄” or “►” to Save.
(
“OK” or “NO USB drive available, please check
and/or insert USB dri…” will be displayed).
Load settings from USB (“OK, reboot TV set“ or
“NO USB drive available,
please check and/or in-
sert USB dri...” will be dis-
played).
Press “
◄” or “►” to Load.
10 ADC ADJUST ADC ADJUST Submenu Press “OK” to enter to ADC ADJUST Submenu
13/17 MODE YPbPr(SD)
Press “ ◄ ” or “ ► ” to change RGB/YPbPr(SD)/ YPbPr(HD).
ADJUST External signal
Press “◄” or “►” to change Internal signal/External signal.
External: factory. Internal: service
R-GAIN 80
Press “
◄” or “►” for manual adjustment.
G-GAIN 70
Press “
◄” or “►” for manual adjustment.