MX-5111N IC card reader 32 – 8
(2) Setting of the HID setting file
For [Decoding\CardId] section, the same as above.
When Data = #!abcde$12345%vxxyz ;
Example 1: Specification by position
Position = 3
Length = 5
Decoded Data = abcde
Example 2: Specification by delimiter
Start.Delimiter = $
End.Delimiter = %
Decoded Data = 12345
When Decoded Data = 12345 ;
Example
Pre = #%
Post = abc
Padded Data = #%12345abc
D. Card reading test
After importing the user area setting to the machine, a test can be
executed to confirm that the cars is properly read. (* User control >
Card area setting > Card reading test (* Only the system settings of
the machine))
Execute "User control > Card area setting > Card scan test"
The result displays after completion of a test are described below.
(When reading is successfully completed, the content of data read
from the card is displayed. When reading is failed, an error display
is made.)
(1) Error displays in case of a reading failure
(2) Display when card reading is successfully
completed
Read Success.
Card ID: XXXXXX
Facility Code: XXXXXX
* When card reading is successfully completed, the result is indi-
cated as shown above with the user information. Check to con-
firm that the displayed items are proper. If not, check the
improper item.
HID setting file template
The extension of “ini” should be added.
Section name Description
Decoding\Facility
Code
Decode setting of the facility code.
(* If the facility code is not used, there is no need to
describe this item.)
Decoding\CardId Decode setting of the card ID.
(* If the card ID is not decoded and all the read data
are used for the card ID, there is no need to describe
this item.)
[ Decoding\FacilityCode]
Key name Description
Location Location specifying method
ByPosition: Specifying by position
ByDelimiter: Specifying by delimiter
* If the facility code has no setting of this item, it is
NULL.
* If the card ID has no setting of this item, all the data
read from the card is made the card ID.
Position Start position (1 - 128) is specified with a decimal
number.
(* Specified only when the location key value is
"ByPosition".)
* The head is specified with 1 and later.
Length Position The length of reading from the position specified with
the key is specified with a decimal number (1 - 128).
(* Specified only when the location key value is
"ByPosition".)
* The total of this set value and the value specified
with Position key must be 128+1 or less.
Start.Delimiter Delimiter (Front)
(* Specified only when the location key value is
"ByDelimiter".)
* Only ASCII code printable characters can be used
for specification.
End.Delimiter Delimiter (Back)
(* Specified only when the location key value is
"ByDelimiter".)
* Only ASCII code printable characters can be used
for specification.
Section name Description
Padding\CardId Card ID padding setting
[Padding\Data]
Key name Description
Pre Front padding (Max. 3 characters)
* Only ASCII code printable characters can be used
for specification.
Post Back padding (Max. 3 characters)
* Only ASCII code printable characters can be used
for specification.
Details of error
Error display Error content and remedy
Card is not
found.
Content Card is not found.
Remedy Check to confirm that the card is securely set
in the card reader.
Read Error. Content A read error occurs.
Remedy Check to confirm that the card and card
reader operate normally with a personal
computer, etc.
hid_template E
;; HID setting file
# General information setting
[General]
Version=1.0
Card=HID
# Decode setting of the facility code
[Decoding\FacilityCode]
Location=ByPosition
Position=1
Length=8
# Decode setting of the card ID
[Decoding\CardId]
Location=ByDelimiter
Start.Delimiter=!
End.Delimiter=?
# Card ID padding setting
[Padding\CardId]
Pre=@@@
Post=\\\
: '11/Jul/25
To Next Page
Loading...
