MX3500N SIMULATION 7 – 46
<List of set items>
<List of result displays>
40-7
Purpose
Setting
Function (Purpose)
Used to set the adjustment value of the
detection level of the manual paper feed
tray paper width detector.
Section
Paper feed
Item
Specifications
Operation/Procedure
1) Select the set item with [↑] and [↓] buttons.
The highlighted set value is switched and the value is dis-
played in the setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and the
operation is invalid.
If there is any item under [↓], an active display is made and
item is shifted.
If there is no item over [↓], the display grays out and the
operation is invalid.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3) When [OK], [↑], [↓] button, [COLOR], or [BLACK] key is
pressed, the currently entered data are saved to EEPROM and
RAM.
<Set range and default value of each setup>
41
41-1
Purpose
Operation test/Check
Function (Purpose)
Used to display the operating state of the
document sensor.
Section
Other
Item
Operation
Operation/Procedure
1) When the machine enters Simulation 41-01, the following
screen is displayed to show the sensor status change.
* When each sensor is turned ON, the corresponding sensor
name is highlighted.
<Sensor name>
41-2
Purpose
Operation test/Check
Function (Purpose)
Used to adjust the detection level of the
document size sensor.
Section
Other
Item
Operation
Operation/Procedure
1) When the machine enters Simulation 41-02, the following
screen is displayed.
Press [EXECUTE] button without a document on OC.
[EXECUTE] button is highlighted and the sensor level setting
without document is performed.
2) The sensor level setting without document is completed.
Set A3 (11" x 17") paper on OC and press [EXECUTE] button.
The sensor level setting with document detection is performed.
3) After completion of sensor level setting with document, the
message is displayed to show the adjustment has been suc-
cessfully completed. (In case of an error, the error message is
displayed with the failed sensor name.)
<Document sensor names, adjustment ranges and default val-
ues>
Display Description of item
MAX POSITION Manual feed max. width
P1 (A4) POSITION Manual feed P1 position width (A4)
P2 (A4R) POSITION Manual feed P2 position width (A4R)
MIN POSITION Manual feed min. width
Item name Item content
COMPLETE Adjustment completed
ERROR Adjustment failed
Item Item Item content
Set
range
Default
value
A MAX POSITION Manual feed max. width 0 to 255 241
B P1 POSITION Manual feed P1 position
(A4)
0 to 255 231
C P2 POSITION Manual feed P2 position
(A4R)
0 to 255 140
D MIN POSITION Manual feed min. width 0 to 255 19
0
SIMULATION
NO.40-02
TEST
BYPASS TRAY ADJUSTMENT
CLOSE
EXECUTE
MAXPOSITION AD JUSTME NT.
PRESS [EXECUTE] TO START
0
A:
A:241 ; MAX POSITION
B : 231 ; P1 POSITION
C : 140 ; P2 POSITION
D : 19 ; MIN POSITION
SIMULATION NO.40-07
BYPASS TRAY VALUE SETTING
241
[ 0~ 255 ]
OK
TEST
CLOSE
Code (Display) Sensor name
OCSW Original cover SW
PD1 Document detection 1
PD2 Document detection 2
PD3 Document detection 3
PD4 Document detection 4
PD5 Document detection 5
PD6 Document detection 6
PD7 Document detection 7
Sensor name Content Set range Default value
PD1 Document sensor 1 0 – 255 128
PD2 Document sensor 2
PD3 Document sensor 3
PD4 Document sensor 4
PD5 Document sensor 5
PD6 Document sensor 6
PD7 Document sensor 7
To Next Page
Loading...
