Sharp PN-V602

31
E
Youcanreturnthesettingstotheirfactory-presetvaluesand
restrict operations.
1. If using the remote control unit, press
SIZE
until “F”
is displayed in the upper left area of the screen, then
while “F” is being displayed, press
, , , and
in that order.
If using the monitor buttons, press
and at the
same time until “F” is displayed in the upper left area
of the screen, then while “F” is being displayed, press
and at the same time.
OFF
UNLOCKED
ON1
ON
LED
OFF
MONITOR
FUNCTION
1/1
ALL RESET
ADJUSTMENT LOCK
ADJUSTMENT LOCK TARGET
RS-232C
OSD DISPLAY
LED
TEMPERATURE ALERT
STATUS ALERT
POWER BUTTON
CONTROLLER INPUT
END
…
[MENU]
2. Select and set the items.
ALL RESET
Resets the settings to the factory default settings.
Press
,selectALLRESET,andthenpress
MENU
.
Afterinitialization,turnthemainpowerswitchoffand
then back on.
WhenthePN-ZB02(optional)isattached,press ,
select the resetting method, and then press
MENU
.
ALLRESET1 ....Resets all the settings to the factory
default settings.
ALLRESET2 ....Returns all settings to the factory default
settings except for the following items:
LANSETUP,RS-232C/LANSELECT,
IDNo.SET,BAUDRATE,NETWORK,
MAIL,SERVICE&SUPPORT,and
SNMP(Seepages24,25,andpages49
to52.)
ADJUSTMENT LOCK
You can disable operations on the monitor and the
remote control unit that use buttons.
OFF ...Enablesoperation.
ON1 ..Disablesalloperationsotherthanturningpower
on/off,FUNCTION,andREMOTECONTROL
MODE.
ON2 ..OnlytheFUNCTIONandREMOTECONTROL
MODEoperationsareenabled.
DisablesalloperationsotherthanFUNCTION
andREMOTECONTROLMODE(notevenpower
on/off).
ADJUSTMENT LOCK TARGET
Sets the target to prohibit operation of with
ADJUSTMENTLOCK.
REMOTECONTROL ...Prohibits remote control operation
MONITORBUTTONS ....Prohibits monitor button operation
BOTH ........................ Prohibits remote control and
monitor button operation
Initialization (Reset)/Functional Restriction Setting (FUNCTION)
RS-232C
(RS-232C/LAN when the PN-ZB02 (optional) is
attached)
SpecieswhethertoallowcontrolviaRS-232CorLAN
(seepages32and45).
OSD DISPLAY
Shows/hides the menu, modes, and messages.
TheFUNCTIONandREMOTECONTROLMODE
screens cannot be hidden.
ON1 ............. Shows all menus, modes, and messages.
ON2 ............. Hides messages automatically displayed
by the display. Shows messages during
operation.
OFF .............. Hides all menus, modes, and messages.
LED
SpecieswhethertolightthepowerLED.
OFFcannotbeselectedwhenSTANDBYMODEisLOW
POWER.
TEMPERATURE ALERT
Selectsthenoticationmethodforanabnormal
temperature.
OFF .............. Donotnotifyaboutanabnormal
temperature.
OSD&LED .. Whenanabnormaltemperatureis
detected,thepowerLEDashesinred
and green alternately and the screen
displaysamessage:TEMPERATURE.
LED............... Whenanabnormaltemperatureis
detected,thepowerLEDashesinred
and green alternately.
STATUS ALERT
Selectsthenoticationmethodforahardwareerror.
OFF .............. Donotnotifyabouttheerror.
OSD&LED .. Whenahardwareerrorisdetected,the
powerLEDashesinredandthescreen
displaysamessage:STATUS[xxxx].
LED............... Whenahardwareerrorisdetected,the
powerLEDashesinred.
POWER BUTTON
Normally, leave this setting as MONITOR.
Whenusinganoptionalpart,ifinstructionappears,
change the setting accordingly.
CONTROLLER INPUT
Normally, you do not need to change this setting.
Whenusinganoptionalpart,ifinstructionappears,
change the setting accordingly.
3. Press
MENU
to return to the normal screen.
TIPS
• Whenbothabnormaltemperatureandhardwareerrorare
detected,thehardwareerrornoticationoverrides.
• IfOSDDISPLAYissettoeitherON2orOFF,anerror
noticationisdisplayedwhenTEMPERATUREALERTor
STATUSALERTissettoOSD&LED.