Sharp PN-V701

63
E
Specications
n
Product Specications
Model PN-V701
LCD component
70" Class [69-1/2 inch (176.6cm) diagonal] TFT LCD
Max. resolution (pixels)
1920 x 1080
Max. colors
Approx. 1.06 billion colors
Pixel pitch
0.802 mm (H) × 0.802 mm (V)
Brightness (typical)
*
1
700 cd/m
2
Contrast ratio (typical)
*
1
4000 : 1
Viewing angle
178° right/left/up/down (contrast ratio ≥ 10)
Screen active area inch (mm)
60-9/16 (W) x 34-1/16 (H) (1538.9 x 865.6)
Computer input signal
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75
Ω
],
DisplayPort 1.2, HDMI
Sync signal
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green *
2
,
Composite sync (TTL: positive/negative) *
2
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
Video Mini D-sub 15 pin, 3 rows x 1
DVI-D 24 pin (HDCP compatible) x 1
HDMI x 2
DisplayPort x 1
Serial (RS-232C)
D-sub 9 pin x 1
Audio
3.5 mm mini stereo jack x 1
Control kit x 1
Output terminals
Video DisplayPort x 1
Serial (RS-232C)
D-sub 9 pin x 1
Audio
3.5 mm mini stereo jack x 1
LAN terminal 10 BASE-T/100 BASE-TX
Expansion slot 13V, 2.0 A
(power supplied when expanding the functions with an optional part)
Power requirement AC 100 V - 240 V, 4.2 A, 50/60 Hz
Operating temperature
*
3
32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption
(Maximum / input signal waiting mode
*
4
*
5
/
standby mode
*
4
*
6
)
380 W / 2.5 W / 0.5 W
Dimensions (excluding protrusions) inch (mm)
Approx. 60-3/4 (W) x 4-13/16 (D) x 34-1/4 (H) (1543.7 x 122 x 870.4)
Weight lbs. (kg)
Approx. 81.6 (37)
*1 When UNIFORMITY is set to MODE1.
Brightness and contrast ratio will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the
nature of the equipment, it is not possible to precisely maintain a constant level of brightness.
*2 D-Sub input terminal only.
*3 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specied by the optional equipments.
*4 When the optional part is not installed.
*5 When NO SIGNAL AUTO INPUT SEL. is set to OFF.
*6 When POWER SAVE MODE is set to ON. When POWER SAVE MODE is set to OFF: 1.0 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
n
PN-ZR02 (optional) Product Specications
Model PN-ZR02
Remote control sensor box dimensions inch (mm)
Approx. 1-3/8 (W) x 7/8 (D) x 5-1/8 (H) (34.2 x 23 x 130)
Remote control sensor box weight lbs. (kg)
Approx. 0.220 (0.1)